Models > ATF8000FS1

ATF8000FS1 Frigidaire Washer - Overview

Sections of the ATF8000FS1

[Viewing 6 of 6]

Manuals & Care Guides for ATF8000FS1

Click to download
Keep searches simple, eg. "belt" or "pump".
Shock Absorber Kit – Part Number: 5304485917
Shock Absorber Kit
★★★★★
★★★★★
(39)
PartSelect #: PS3508101
Manufacturer #: 5304485917
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
$50.60
  In Stock
Front Load Washer Door Lock and Switch Assembly – Part Number: 131763256
Front Load Washer Door Lock and Switch Assembly
★★★★★
★★★★★
(36)
PartSelect #: PS12364048
Manufacturer #: 131763256
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
$176.03
  In Stock
Door Striker – Part Number: 131763302
Door Striker
★★★★★
★★★★★
(12)
PartSelect #: PS2378364
Manufacturer #: 131763302
This part is found on the door of your washer and keeps your door closed for use.
$25.71
  In Stock
Water Inlet and Dispenser Valve – Part Number: 134371220
Water Inlet and Dispenser Valve
★★★★★
★★★★★
(12)
PartSelect #: PS1145692
Manufacturer #: 134371220
This part comes with the sensor/thermistor.
$161.95
  In Stock
Drain Pump - 120V 60  Hz. – Part Number: 137221600
Drain Pump - 120V 60 Hz.
★★★★★
★★★★★
(18)
PartSelect #: PS7783938
Manufacturer #: 137221600
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$211.15
  In Stock
Door Hinge with Bushings – Part Number: 134550800
Door Hinge with Bushings
★★★★★
★★★★★
(7)
PartSelect #: PS1152380
Manufacturer #: 134550800
This part attaches to the outside of the front door panel to help with the door open and closing properly.
  No Longer Available
Screw – Part Number: 131302800
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
  In Stock
Screw-In Plastic Leveling Leg – Part Number: 134548800
Screw-In Plastic Leveling Leg
PartSelect #: PS1152204
Manufacturer #: 134548800
Sold individually.
$33.09
  In Stock
Single Shock Mounting Pin – Part Number: 131268300
Single Shock Mounting Pin
PartSelect #: PS417323
Manufacturer #: 131268300
$29.93
  In Stock
Drain Hose – Part Number: 134455900
Drain Hose
★★★★★
★★★★★
(4)
PartSelect #: PS975871
Manufacturer #: 134455900
Also known as tub-to-pump drain hose.
$78.87
  In Stock
Drum Vane – Part Number: 134509600
Drum Vane
★★★★★
★★★★★
(1)
PartSelect #: PS1145727
Manufacturer #: 134509600
Sold individually.
$171.26
  In Stock
Door Glass – Part Number: 134366400
Door Glass
★★★★★
★★★★★
(4)
PartSelect #: PS1145708
Manufacturer #: 134366400
$306.09
  In Stock

Questions And Answers for ATF8000FS1

Ask our experts a question about this model and we'll get back to you as soon as possible!

4 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
April 12, 2023
my machine will not leave perm press. It also just cuts off within 5 seconds. it shows what looks like 1hs on screen. I changes the switch a while back HELP
For model number ATF8000FS1
PartSelect logo
Hi Michael, thank you for reaching out. Based on the description that you have provided, we would recommend checking the control board, part number PS16731247, and replacing it if necessary. We hope this solves your problem!

Was this helpful?
Thank you for voting!
Related Parts:
Andrew
July 7, 2023
Washer starts and runs for only 15sec. Before it shuts down. Shows E57 on display
For model number ATF8000FS1
PartSelect logo
Hi Andrew, thank you for reaching out. E57 code means that your motor control board is drawing too much power. To solve this issue, you may need to check the motor control board, part number PS1524621, as it is most likely faulty and may need to be replaced. Let us know if you have further questions!

Was this helpful?
Thank you for voting!
Related Parts:
Roger
November 5, 2023
The machine cycled through and overflows and not draining is it the pump not working?
For model number ATF8000FS1
PartSelect logo
Hello Roger, thank you for the question. Based on the description that you have provided, we would recommend checking the pressure switch for continuity. If this is not the issue, you may need to replace the drain pump, part number PS7783938. Glad to be of assistance!

Was this helpful?
Thank you for voting!
Related Parts:
Gerald
April 23, 2024
After a few minutes my machine shuts off and says paused.
For model number ATF8000FS1
PartSelect logo
Hello Gerald, thank you for getting in touch. Based on our understanding of the issue, we would suggest checking the control board, part number PS16731247, to solve the problem. We hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the ATF8000FS1

[Viewing 13 of 13]
Lid or door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Locking Issues
Fixed by
these parts
Fixing Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Burning smell
Fixed by
these parts
Fixing
Show All
Not draining
Fixed by
these parts
Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door on washer wouldn't lock or start
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • DOUG from KING FERRY, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
472 of 554 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both vibration shock absorbers broken
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.
Parts Used:
Shock Absorber Kit
  • Douglas from Medical Lake, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
179 of 192 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would't spin all water out or rinse out clothes
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.
Parts Used:
Drain Pump - 120V 60 Hz.
  • kenneth from willard, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
167 of 203 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!