Models > ATW4475XQ0

ATW4475XQ0 Admiral Washer - Overview

Sections of the ATW4475XQ0

[Viewing 8 of 8]
Keep searches simple, eg. "belt" or "pump".
Direct Drive Motor Coupling – Part Number: 285753A
Direct Drive Motor Coupling
★★★★★
★★★★★
(63)
PartSelect #: PS1485646
Manufacturer #: 285753A
This coupling kit is located between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.
$35.42
  In Stock
Suspension Spring – Part Number: WP63907
Suspension Spring
★★★★★
★★★★★
(4)
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$10.18
  In Stock
Clutch Assembly – Part Number: 285785
Clutch Assembly
★★★★★
★★★★★
(41)
PartSelect #: PS334641
Manufacturer #: 285785
A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring f...
$38.04
  In Stock
Agitator Bolt – Part Number: WP358237
Agitator Bolt
★★★★★
★★★★★
(5)
PartSelect #: PS11741866
Manufacturer #: WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$8.94
  In Stock
Touch-Up Paint - White – Part Number: 72017
Touch-Up Paint - White
★★★★★
★★★★★
(16)
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.18
  In Stock
Washer Lid Switch – Part Number: WP8318084
Washer Lid Switch
★★★★★
★★★★★
(17)
PartSelect #: PS11745957
Manufacturer #: WP8318084
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the grounding wire.
$58.44
  In Stock
Washer Water Inlet Valve with Thermistor – Part Number: WPW10144820
Washer Water Inlet Valve with Thermistor
★★★★★
★★★★★
(29)
PartSelect #: PS11749042
Manufacturer #: WPW10144820
This part is used to help control and balance the water temperature flowing in to the washer tub.
$80.98
  In Stock
Thrust Spacer – Part Number: 285587
Thrust Spacer
★★★★★
★★★★★
(1)
PartSelect #: PS334562
Manufacturer #: 285587
This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ...
$8.44
  In Stock
Tub Wear Pads - Package of 3 – Part Number: 285744
Tub Wear Pads - Package of 3
★★★★★
★★★★★
(8)
PartSelect #: PS334620
Manufacturer #: 285744
This package of pads contains three tub wear pads.
$21.41
  In Stock
Agitator Repair Kit – Part Number: 285748
Agitator Repair Kit
★★★★★
★★★★★
(16)
PartSelect #: PS334622
Manufacturer #: 285748
This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with th...
$46.38
  In Stock
Centerpost Gasket – Part Number: W10814296
Centerpost Gasket
★★★★★
★★★★★
(6)
PartSelect #: PS11723081
Manufacturer #: W10814296
Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.
$7.34
  In Stock
Foot, Front - Single – Part Number: WPW10001130
Foot, Front - Single
★★★★★
★★★★★
(3)
PartSelect #: PS11747965
Manufacturer #: WPW10001130
Sold Individually.
$9.47
  In Stock

Questions And Answers for ATW4475XQ0

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

5 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kathy
February 2, 2020
What is the cu?
For model number ATW4475XQ0
PartSelect logo
Hello Kathy, Thank you for the question. We believe this question is best addressed by the manufacturer. We are a parts distributor. We do not manufacture any units, or have access to dimensions and year of manufacture for the models. Please contact your unit's manufacturer, directly. We hope this helps.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Jeff
November 1, 2022
Washer has excessive grease or thick oil, seeping out from under the unit.
For model number ATW4475XQ0
PartSelect logo
Hello Jeff, thank you for reaching out. We have researched your model and found that this issue could be caused by a damaged Oil Seal Kit, part number PS334494. If that does not help, replace the Gear Case Seal, part number PS11741173. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Related Parts:
Jonathan
October 10, 2023
Water leaks out when filling, makes falling sound onto ground hoses are in good shape.
For model number ATW4475XQ0
PartSelect logo
Hi Jonathan, thank you for contacting us. We believe your washer is having this problem due to a faulty centerpost gasket, part number PS11723081, which may need to be replaced. We hope this helps, good luck with the repair!

Was this helpful?
Thank you for voting!
Related Parts:
Johnny
January 28, 2024
Will stop filling when first stared and will not fill on spin cycle
For model number ATW4475XQ0
PartSelect logo
Hello Johnny, thank you for getting in touch. Based on our understanding of the issue, we would suggest checking the water inlet valve, part number PS11749042, to solve the problem. Glad to be of assistance!

Was this helpful?
Thank you for voting!
Related Parts:
Stephen
May 7, 2024
High pitch nose when draining
For model number ATW4475XQ0
PartSelect logo
Hi Stephen, thank you for the question. The drain pump might be clogged or defective. Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the drain pump, remove the drain pump, part number PS11752069, and check the pump for any obstructions. If the drain pump is not clogged, you will not need to replace it. Good luck with the repair!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the ATW4475XQ0

[Viewing 14 of 14]
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing Fixing Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing Fixing Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Parts Used:
Direct Drive Motor Coupling
  • Jeff from Wayne, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1092 of 1176 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spin cycle did not engage
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly
Parts Used:
Clutch Assembly
  • Andrew from SLC, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
488 of 521 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't run
I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire. The new switch drops right in. I had a little trouble getting it in until I realized the washer lid had to be open. A little awkward but once it's in you can shut the lid and then I reattached the wire from the control panel and screwed in the grounding wire. Pretty easy. $20 for the part (with shipping) and 15 minutes. Way cheaper than a repairman.
Parts Used:
Washer Lid Switch
  • Clint from Kansas City, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
325 of 366 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!