Models > DE100ADD1

DE100ADD1 Westinghouse Dryer - Overview

Sections of the DE100ADD1

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
★★★★★
★★★★★
(63)
PartSelect #: PS459829
Manufacturer #: 5303281153
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$71.08
  In Stock
Door Latch Kit – Part Number: 5366021400
Door Latch Kit
★★★★★
★★★★★
(20)
PartSelect #: PS475419
Manufacturer #: 5366021400
This door latch kit comes with the strike and the catch.
$64.47
  In Stock
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(7)
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$8.07
  In Stock
Main Terminal Block Kit – Part Number: 5304409888
Main Terminal Block Kit
★★★★★
★★★★★
(8)
PartSelect #: PS471605
Manufacturer #: 5304409888
Terminal blocks (also called terminal boards or strips) provide a convenient means of connecting individual electrical wires.
$11.95
  In Stock
Idler Pulley Assembly – Part Number: 5303212849
Idler Pulley Assembly
PartSelect #: PS457526
Manufacturer #: 5303212849
Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.
  No Longer Available
Flat Style Belt – Part Number: 5303281154
Flat Style Belt
★★★★★
★★★★★
(1)
PartSelect #: PS459830
Manufacturer #: 5303281154
This is a flat style ridgeless dryer belt.
$19.67
  In Stock
BAFFLE – Part Number: 3204254
BAFFLE
PartSelect #: PS446417
Manufacturer #: 3204254
$139.53
  In Stock
BUSHING/FOOT KIT – Part Number: 5303937190
BUSHING/FOOT KIT
PartSelect #: PS1156911
Manufacturer #: 5303937190
$75.04
  Special Order
Lint Screen and Frame Kit – Part Number: 5303937128
Lint Screen and Frame Kit
PartSelect #: PS470308
Manufacturer #: 5303937128
This dryer lint screen and frame is used for Frigidaire/WCI brand electric and gas dryers. The filter is 14-1/4 inches wide and comes with a bezel frame and mounting screws.
  No Longer Available
Door Switch – Part Number: 5303261027
Door Switch
PartSelect #: PS457587
Manufacturer #: 5303261027
  No Longer Available
GASKET-DOOR – Part Number: 5303201210
GASKET-DOOR
PartSelect #: PS454309
Manufacturer #: 5303201210
  No Longer Available
DISCONTINUED – Part Number: 5300603182
DISCONTINUED
PartSelect #: PS450991
Manufacturer #: 5300603182
  No Longer Available

Questions And Answers for DE100ADD1

Be the first to ask our experts a question about this model!

Common Symptoms of the DE100ADD1

[Viewing 10 of 10]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
334 of 351 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Catch broke, door wouldn't stay closed.
Used a screwdriver to pop out broken piece. Used pliers to snap in new one.
Parts Used:
Door Latch Kit
  • Dianne from Kansas City, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
72 of 77 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Parts Used:
Main Terminal Block Kit
  • Timothy from Spring Valley, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
95 of 149 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!