Models > DE412

DE412 Maytag Dryer - Overview

Sections of the DE412

[Viewing 10 of 10]
Keep searches simple, eg. "belt" or "pump".
Drum Support Roller Kit – Part Number: 12001541
Drum Support Roller Kit
★★★★★
★★★★★
(54)
PartSelect #: PS1570070
Manufacturer #: 12001541
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once.
$19.12
  In Stock
Tumbler and Motor Belt – Part Number: WPY312959
Tumbler and Motor Belt
★★★★★
★★★★★
(48)
PartSelect #: PS11757542
Manufacturer #: WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$41.21
  In Stock
Roller Shaft – Part Number: WP6-3129480
Roller Shaft
★★★★★
★★★★★
(1)
PartSelect #: PS11743031
Manufacturer #: WP6-3129480
This roller shaft is the axle for the drum roller, also known as drum roller axle.
$12.47
  In Stock
Front Glide Kit – Part Number: 306508
Front Glide Kit
★★★★★
★★★★★
(7)
PartSelect #: PS1804752
Manufacturer #: 306508
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
$18.69
  In Stock
Blower Wheel with Clamp – Part Number: Y303836
Blower Wheel with Clamp
★★★★★
★★★★★
(40)
PartSelect #: PS2200270
Manufacturer #: Y303836
This blower wheel comes with a metallic hub clamp to hold it firmly in place.
$29.08
  In Stock
Lint Filter – Part Number: WP33001003
Lint Filter
★★★★★
★★★★★
(42)
PartSelect #: PS11741039
Manufacturer #: WP33001003
This lint filter screen is slide in styl type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.
$31.85
  In Stock
Retaining Ring – Part Number: WP9703438
Retaining Ring
★★★★★
★★★★★
(3)
PartSelect #: PS11746909
Manufacturer #: WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
$10.01
  In Stock
Drum Roller Shaft Washer – Part Number: WP312535
Drum Roller Shaft Washer
PartSelect #: PS11740748
Manufacturer #: WP312535
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
$17.53
  In Stock
Idler Pulley Wheel – Part Number: WP6-3037050
Idler Pulley Wheel
★★★★★
★★★★★
(1)
PartSelect #: PS11743028
Manufacturer #: WP6-3037050
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
$24.49
  In Stock
Front or Rear Drum Felt Seal – Part Number: WP314820
Front or Rear Drum Felt Seal
★★★★★
★★★★★
(2)
PartSelect #: PS11740771
Manufacturer #: WP314820
This front or rear dryer drum felt seal is seventy-nine and a half inches long.
$36.79
  In Stock
Idler Pulley Shaft Washer – Part Number: WPY312527
Idler Pulley Shaft Washer
★★★★★
★★★★★
(2)
PartSelect #: PS11757538
Manufacturer #: WPY312527
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
$17.10
  In Stock
Door Latch Kit – Part Number: 306436
Door Latch Kit
★★★★★
★★★★★
(9)
PartSelect #: PS2029855
Manufacturer #: 306436
This dryer door latch kit comes in two pieces: a door latch, and a door strike. It's used to help hold your door shut to your dryer.
$12.64
  In Stock

Questions And Answers for DE412

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

6 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Felix
January 25, 2022
How can I get to the belt ?
For model number DE412
PartSelect logo
Hello Felix, thank you for the question. We have attached a video on replacing the Belt. We hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Ramon Jasso
February 21, 2020
Starts and heats but tumbler will not turn. I think it needs the belt..ps11757542 .$17.26.but not certain to order or not
For model number DE412
PartSelect logo
Hello Ramon, thank you for your question. The most common cause of a dryer that will not tumble is a broken belt, which is Tumbler and Motor Belt Part Number: WPY312959. Good luck with your repair!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Peggy
September 3, 2021
Have replaced heater & other parts regarding dryer not working, dryer will only heat for 15 minutes. Could it be the timer?
For model number DE412
PartSelect logo
Hello Peggy, Thank you for the question. If all three Thermostats and the Thermal Fuse have been tested or replaced along with the heater, the Timer could be defective. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Related Parts:
Bev
February 24, 2022
Need parts number for the lint filter cavity wall that is a plastic grid.
For model number DE412
PartSelect logo
Hello Bev, thank you for writing. The part you are requesting on has been discontinued and we have no known replacement listed in our system. We have no further information. You are welcome to contact the manufacturer of the part to see if they have recently released a new substitute. Good luck with your repair.

Was this helpful?
Thank you for voting!
Russ
January 13, 2023
Dryer will only run if I keep the start button depressed. What part do I need to make it run.
For model number DE412
PartSelect logo
Hi Russ, thank you for reaching out. The issue seems to be with the Door Switch, we would recommend checking it as it may become faulty, the part number is PS1964648. If that does not help, we would recommend checking the Thermal Fuse, part number PS11740678. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2

Common Symptoms of the DE412

[Viewing 6 of 6]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Too hot
Fixed by
these parts
Fixing Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing Fixing
Show All
Won’t Start
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
noisy rollers, broken latch
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Parts Used:
Door Latch Kit Drum Support Roller Kit
  • gerry from west covina,, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable), Wrench set
651 of 679 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Parts Used:
Blower Wheel with Clamp
  • Stephen from Lafayette, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
565 of 571 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electric dryer was rumbling - wheel or belt?
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
Parts Used:
Tumbler and Motor Belt Blower Wheel with Clamp Lint Filter
  • Raymond from West Bend, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
595 of 702 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!