Models > DE500PXW1

DE500PXW1 Westinghouse Dryer - Overview

Sections of the DE500PXW1

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(7)
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$8.07
  In Stock
Main Terminal Block Kit – Part Number: 5304409888
Main Terminal Block Kit
★★★★★
★★★★★
(8)
PartSelect #: PS471605
Manufacturer #: 5304409888
Terminal blocks (also called terminal boards or strips) provide a convenient means of connecting individual electrical wires.
$11.95
  In Stock
Idler Pulley Assembly – Part Number: 5303212849
Idler Pulley Assembly
PartSelect #: PS457526
Manufacturer #: 5303212849
Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.
  No Longer Available
Flat Style Belt – Part Number: 5303281154
Flat Style Belt
★★★★★
★★★★★
(1)
PartSelect #: PS459830
Manufacturer #: 5303281154
This is a flat style ridgeless dryer belt.
$19.67
  In Stock
Idler Spring – Part Number: 5303281085
Idler Spring
PartSelect #: PS459789
Manufacturer #: 5303281085
With the spring it helps keep the tension in the belt by pulling the idler pulley.
$15.66
  Special Order
Lint Screen and Frame Kit – Part Number: 5303937128
Lint Screen and Frame Kit
PartSelect #: PS470308
Manufacturer #: 5303937128
This dryer lint screen and frame is used for Frigidaire/WCI brand electric and gas dryers. The filter is 14-1/4 inches wide and comes with a bezel frame and mounting screws.
  No Longer Available
DISCONTINUED – Part Number: 5300603182
DISCONTINUED
PartSelect #: PS450991
Manufacturer #: 5300603182
  No Longer Available
DISCONTINUED – Part Number: 5300150495
DISCONTINUED
PartSelect #: PS450292
Manufacturer #: 5300150495
  No Longer Available
HEATER COIL KIT – Part Number: 5300142885
HEATER COIL KIT
PartSelect #: PS450273
Manufacturer #: 5300142885
  No Longer Available
Upper Front Glide and Seal Kit – Part Number: 5300142887
Upper Front Glide and Seal Kit
PartSelect #: PS450274
Manufacturer #: 5300142887
$231.16
  Special Order
DISCONTINUED – Part Number: 5300142888
DISCONTINUED
PartSelect #: PS450275
Manufacturer #: 5300142888
  No Longer Available
DISCONTINUED – Part Number: 5300151521
DISCONTINUED
PartSelect #: PS450295
Manufacturer #: 5300151521
  No Longer Available

Questions And Answers for DE500PXW1

Be the first to ask our experts a question about this model!

Common Symptoms of the DE500PXW1

[Viewing 7 of 7]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Parts Used:
Main Terminal Block Kit
  • Timothy from Spring Valley, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
95 of 149 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Dryer Belt
1st I pried the dryer top open then disconnected the two wires for the auto shut-off. Removed four nuts with driver that opens front and releases dryer barrel. Lifted front up a bit to remove from two lower tabs at bottom of unit and put aside.

I then slid the belt over the barrel noting the side up directions on the belt. On the lower left on the back of unit I opened up the vented cover to reveal the motor pulley and belt tension pulley. I put the belt on the pulley and brought the belt tension pulley over the belt. I then aligned the belt to the proper point on the barrel and reattached the front being careful to center the barrel onto the rim that is built into the front. Take care to align all the tabs and shims in the correct order so that barrel rotates freely. Replace auto shut off wires to switch on inside of front and close top.
Parts Used:
Flat Style Belt
  • Tod from West Springfield, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench set
22 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt Broke
Very easy install. Removed the top and front of dryer, and put new belt on drum. Also replaced Idler Pulley (altho didn't really need to.)
I've had the dryer more than 20 years, so I am really glad such a simple repair will keep it going!
Parts arrived very quickly - great service from PastSelect!
Parts Used:
Flat Style Belt Idler Spring Idler Pulley Assembly
  • Patricia from Clifton Park, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!