Models
>
DLE330RAW
DLE330RAW Amana Dryer - Overview
Sections of the DLE330RAW
[Viewing 7 of 7]Keep searches simple, eg. "belt" or "pump".
Multi Rib Belt
PartSelect #: PS11742271
Manufacturer #: WP40111201
This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
$12.00
In Stock
Drum Support Roller
PartSelect #: PS11741913
Manufacturer #: WP37001042
This single drum support roller is used for square ported model clothes dryers. It has a metallic bearing in its center.
$26.63
In Stock
Door Catch Kit
PartSelect #: PS2162263
Manufacturer #: LA-1003
This kit comes in two pieces: the catch and the clip.
$41.11
In Stock
Lint Filter
PartSelect #: PS11741919
Manufacturer #: WP37001142
Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.
$99.40
In Stock
Idler Pulley Wheel with Bearing
PartSelect #: PS11757553
Manufacturer #: WPY54414
This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.
$28.32
In Stock
High Limit Thermal Fuse
PartSelect #: PS11742274
Manufacturer #: WP40113801
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
$16.48
In Stock
Door Switch Kit
PartSelect #: PS1964648
Manufacturer #: W10169313
This part replaces older two terminal switches.
$38.07
In Stock
Thrust Washer
PartSelect #: PS11740482
Manufacturer #: WP233520
This washer is 3/4 inches in diameter.
$10.11
In Stock
Cylinder Felt Seal
PartSelect #: PS11741917
Manufacturer #: WP37001132
This part is located between the back of the drum and the rear dryer panel.
$65.74
In Stock
Cylinder Glide Bracket
PartSelect #: PS11741912
Manufacturer #: WP37001036
These brackets support each side of the tub. Order quantity needed.
$82.21
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$6.88
In Stock
Questions And Answers for DLE330RAW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DLE330RAW
[Viewing 10 of 10]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
Parts Used:
-
Chris from Hopedale, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
524 of 547 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Parts Used:
-
Tim from South Glens Falls, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
498 of 504 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Filter Lint Was Broken
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise.
Parts Used:
-
Mirsada from Yorktown Heights, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
378 of 381 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!