Models > FCM15HDPAWH

FCM15HDPAWH General Electric Freezer - Overview

Sections of the FCM15HDPAWH

[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Key – Part Number: WR01X26468
Key
PartSelect #: PS11729544
Manufacturer #: WR01X26468
This key is for freezers. If your key will not lock or unlock the freezer door, check it to see if it has been bent or damaged. If it has been damaged, you should look to replace it to avoid damaging ...
  No Longer Available
CONTROL TEMP – Part Number: WR09X10059
CONTROL TEMP
PartSelect #: PS288229
Manufacturer #: WR09X10059
  No Longer Available
COLD CONTROL KNOB – Part Number: WR02X10860
COLD CONTROL KNOB
PartSelect #: PS285268
Manufacturer #: WR02X10860
$77.76
  Special Order
Drain Plug – Part Number: WR02X10073
Drain Plug
PartSelect #: PS284532
Manufacturer #: WR02X10073
$51.73
  Special Order
POWER ON LIGHT – Part Number: WR23X10052
POWER ON LIGHT
PartSelect #: PS296041
Manufacturer #: WR23X10052
  No Longer Available
Gasket – Part Number: WR24X10005
Gasket
PartSelect #: PS296700
Manufacturer #: WR24X10005
  No Longer Available
SWITCH LIGHT – Part Number: WR23X10303
SWITCH LIGHT
PartSelect #: PS759479
Manufacturer #: WR23X10303
$117.23
  Special Order
SCREW HEX WASHER HEAD 1 – Part Number: WR01X10823
SCREW HEX WASHER HEAD 1
PartSelect #: PS2345736
Manufacturer #: WR01X10823
$25.20
  Special Order
DRIER-FILTER – Part Number: WR86X10005
DRIER-FILTER
PartSelect #: PS309869
Manufacturer #: WR86X10005
$81.66
  Special Order
SCREW TOE GR – Part Number: WR1X2209
SCREW TOE GR
PartSelect #: PS294958
Manufacturer #: WR1X2209
$10.09
  Special Order
WASHER FLAT – Part Number: WR01X10164
WASHER FLAT
PartSelect #: PS283613
Manufacturer #: WR01X10164
  No Longer Available
SUPPORT COMPRESSOR – Part Number: WR17X3339
SUPPORT COMPRESSOR
PartSelect #: PS293258
Manufacturer #: WR17X3339
  No Longer Available

Questions And Answers for FCM15HDPAWH

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Moldy Gasket
This freezer was given to me by a neigbor. It had set closed/unplugged for over a year. The gasket was so moldy I couldn't clean it. Unplug the freezer! I removed the old gasket pins using needle nose pliers. There were about 50 plastic pens holding the gasket and inside cover of the freezer lid (chest freezer) The plastic pens were difficult to remove. The insulation was wet so I braced the lid open and let the insulation dry for a couple of days. When the insulation was dry I attached a plastic pen at each corner of the gasket and then placed pens at even intervals around the rest of the gasket.. None of the holes lined up past the 3rd hole so I used a punch to make the necessary holes. The instructions say to put a bead of silicone gel around the outer edge of the gasket. I haven't done that yet but plan to do that last step.
Parts Used:
Gasket
  • Ouida from Huntsville, AL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The freezer was missing the key
I ordered a pair of new keys from Parts Select and found the website extremely easy to use. I found the key I needed in less than 10 minutes and ordered the item. The key woked perfectly. Delivery was prompt and the cost was resonable. I have bookmarked the site for future use. thank you. James
Parts Used:
Key
  • james from las cruces, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two of the two leveling jacks of this old refrigerator were missing and had to be replaced.
I ordered four leveling jacks from this site for the refrigerator using a slightly different model number (my model was not listed). I assumed that the jacks all had the same shaft diameter and thread size. However, it turned out that the two front jacks had half-inch shaft diameters. It could be that originally there were rollers in front. The two rear jacks had quarter-inch shafts with "feet" for supporting them on the floor. So, I had to return the four jacks I had ordered and find another solution. I found two half-inch threaded bolts at the local hardware store that fit the front holes perfectly. I purchased 3.5 inch bolts to give me enough room to find the proper adjustment. I used wooden blocks and a crow bar to raise one side of the refrigerator high enough to screw in the leveling jacks. I used an adjustable crescent wrench to turn the bolts' hex heads until they were the proper height. I used the two original quarter-inch jacks in the rear holes and adjusted them to the proper height to level the refrigerator on the concrete floor where it is located. Then I removed the wooden blocks and tested to make sure the refrigerator did not wobble. I found that using the two bolts (no leveling jacks for the front holes could be found) for the front jacks proved to be the ideal solution. The job took me about thirty minutes, including the time it took to move the refrigerator into its final location and adjust the leveling jacks once more to create a solid stance so that the refrigerator did not wobble. While I had the refrigerator away from the wall, I removed the rear panel and cleaned the blades of the cooler fan and removed dust and dirt build up near the compressor with a vacuum cleaner. Then, I screwed the panel back into position, moved the refrigerator into its final place in a corner of the garage and made sure there was enough air space around it to allow for proper air circulation. This took me about twenty more minutes. I plugged it back in and listened to it come alive again. It is old but has never needed a repair and keeps everything cooled or frozen. I would suggest using threaded hex-head bolts in place of original leveling jacks if they cannot be obtained. Problem solved.
Parts Used:
LEVELNG JACK
  • Bruce K from RESTON, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!