Models > FEX831CS0

FEX831CS0 Frigidaire Washer Dryer Combo - Overview

Sections of the FEX831CS0

[Viewing 8 of 8]

Manuals & Care Guides for FEX831CS0

Click to download
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
★★★★★
★★★★★
(65)
PartSelect #: PS459829
Manufacturer #: 5303281153
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$79.28
  In Stock
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(7)
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$8.04
  In Stock
Drum Glide - White – Part Number: 137513300
Drum Glide - White
★★★★★
★★★★★
(3)
PartSelect #: PS5574052
Manufacturer #: 137513300
Appliance requires 2 .Sold individually.
$44.93
  In Stock
Thermal Limiter - Limit 220 – Part Number: 134120900
Thermal Limiter - Limit 220
★★★★★
★★★★★
(11)
PartSelect #: PS419402
Manufacturer #: 134120900
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.56
  In Stock
Dryer Lint Screen – Part Number: 5304516871
Dryer Lint Screen
★★★★★
★★★★★
(16)
PartSelect #: PS12585473
Manufacturer #: 5304516871
This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.
$65.91
  In Stock
Drive V-Belt – Part Number: 134511600
Drive V-Belt
★★★★★
★★★★★
(17)
PartSelect #: PS1146950
Manufacturer #: 134511600
This belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$31.69
  In Stock
Drain Pump - 120V 60  Hz. – Part Number: 137221600
Drain Pump - 120V 60 Hz.
★★★★★
★★★★★
(19)
PartSelect #: PS7783938
Manufacturer #: 137221600
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$220.77
  In Stock
Lower Front Felt Seal with Adhesive – Part Number: 5303937183
Lower Front Felt Seal with Adhesive
★★★★★
★★★★★
(9)
PartSelect #: PS832645
Manufacturer #: 5303937183
$32.29
  In Stock
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(4)
PartSelect #: PS418433
Manufacturer #: 131658800
This part helps keep the door closed while the machine is running.
$79.66
  In Stock
Multi-Rib Drum Belt – Part Number: 137292700
Multi-Rib Drum Belt
★★★★★
★★★★★
(3)
PartSelect #: PS3408299
Manufacturer #: 137292700
This belt helps rotate from the drive motor to the drum.
$24.94
  In Stock
Front Upper Felt Seal with Adhesive – Part Number: 5303937182
Front Upper Felt Seal with Adhesive
PartSelect #: PS832644
Manufacturer #: 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$31.94
  In Stock
Door Strike – Part Number: 5303207102
Door Strike
★★★★★
★★★★★
(6)
PartSelect #: PS455020
Manufacturer #: 5303207102
"Male" piece of a dryer door closing mechanism.
$23.90
  In Stock

Questions And Answers for FEX831CS0

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

24 questions answered by our experts.
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
December 15, 2019
The dryer has started making a high pitched squeal when turned on. At first, it was random and would go away after warmed up. But now, the screeching sound is continuous. The unit is over 10 years old, but has worked great until now. Your thoughts?
For model number FEX831CS0
PartSelect logo
Hello James, thank you for your question. That type of issue is usually caused by the PartSelect Number: PS3408299 belt and rear drum bearing PartSelect #: PS459829. I hope this helps!

8 people found this helpful.

Was this helpful?
Thank you for voting!
Rodd
February 4, 2020
Washing machine won’t automatically go through it’s cycles. It has to be turned manually.
For model number FEX831CS0
PartSelect logo
Hello Rodd, Thank you for the question. This sounds like the Timer PartSelect Number PS418697 is defective and will need to be replaced. We hope this helps.

3 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Jan
February 13, 2020
Could you please tell me the capacity of the wash tub and the dryer? Also, two other issues. 1-. dryer makes loud screeching noise when turned on, then noise quites in a few minutes. what part would i need? since it's 15 years old i don't want to put too much into it. if i continue to use without replacing this part, will it cause furthur damage? 2-. i have taken dryer apart when i bought it used and cleaned lint out thoughly. it still leaves much lint on clothes. vent does collect well and properly seeled. lint chunks hand up in door, but lint still on clothes once they are dry. any possible solutions? thanks much.
For model number FEX831CS0
PartSelect logo
Hi Jan, thank you for your question. Both are 5.7 cu ft. For your dryer you may want to check your felt seals and your ball hitch bearing. It could be that one or all of those parts have worn out and just need to be replaced. If you are getting excessive lint on your clothes you may need to clean the filter with some hot soapy water. It might be that it is clogged. You may also want to check the inside ducts of the appliance and make sure there is no build up on lint inside of the dryer duct itself. Good luck with your repair.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Steve
January 3, 2023
The water does not shut off after filling washer
For model number FEX831CS0
PartSelect logo
Hello Steve, thank you for contacting us. There could be two probable reasons why the water does not shut off after filling your washing machine. It is possible that the water inlet valve, part number PS815534, which controls the flow of water into the washing machine, is faulty or clogged. Another possibility is that the water level switch, part number PS1146954, which is responsible for detecting the water level in the washing machine and turning off the water flow when it reaches a certain level, is not working properly. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Deborah
September 30, 2023
This stackable washer/dryer came with my rental condo but maintenance doesn't cover it and the washer is leaking from drain pump. What can I check before I call a repair service, Dryer is fine. How do I know if this is gas or electric?
For model number FEX831CS0
PartSelect logo
Hi Deborah, thank you for the question. Based on our research, it is an electric dryer/washer combo. For the leaking issue, you may need to check the drain hose for clogging and also check the tub seals for any damage. If both are fine, we would recommend replacing the drain pump, part number PS7783938, to fix the issue. We hope this information helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2
  • 3

Common Symptoms of the FEX831CS0

[Viewing 13 of 13]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
Too hot
Fixed by
these parts
Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Not draining
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
334 of 353 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Parts Used:
Drive V-Belt
  • rodney from fairfield bay, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
278 of 310 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermal Limiter opened
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.
Parts Used:
Thermal Limiter - Limit 220
  • Stephen from Newnan, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
244 of 320 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!