Models > FTF2140FS1

FTF2140FS1 Frigidaire Washer - Overview

Sections of the FTF2140FS1

[Viewing 5 of 5]

Manuals & Care Guides for FTF2140FS1

Click to download
Keep searches simple, eg. "belt" or "pump".
Door Strike – Part Number: 131763310
Door Strike
★★★★★
★★★★★
(65)
PartSelect #: PS890617
Manufacturer #: 131763310
The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not star...
$19.58
  In Stock
Shock Absorber Kit – Part Number: 5304485917
Shock Absorber Kit
★★★★★
★★★★★
(39)
PartSelect #: PS3508101
Manufacturer #: 5304485917
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
$50.60
  In Stock
Front Load Washer Door Lock and Switch Assembly – Part Number: 131763256
Front Load Washer Door Lock and Switch Assembly
★★★★★
★★★★★
(36)
PartSelect #: PS12364048
Manufacturer #: 131763256
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
$176.03
  In Stock
Door Handle – Part Number: 134412860
Door Handle
★★★★★
★★★★★
(13)
PartSelect #: PS2330842
Manufacturer #: 134412860
Handle ONLY.
$78.07
  In Stock
Drain Pump - 120V 60  Hz. – Part Number: 137221600
Drain Pump - 120V 60 Hz.
★★★★★
★★★★★
(18)
PartSelect #: PS7783938
Manufacturer #: 137221600
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$211.15
  In Stock
Bellow Kit – Part Number: 134515300
Bellow Kit
★★★★★
★★★★★
(7)
PartSelect #: PS1148773
Manufacturer #: 134515300
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
$393.85
  In Stock
Screw – Part Number: 131302800
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
  In Stock
Screw-In Plastic Leveling Leg – Part Number: 134548800
Screw-In Plastic Leveling Leg
PartSelect #: PS1152204
Manufacturer #: 134548800
Sold individually.
$33.09
  In Stock
Single Shock Mounting Pin – Part Number: 131268300
Single Shock Mounting Pin
PartSelect #: PS417323
Manufacturer #: 131268300
$29.93
  In Stock
Drain Hose – Part Number: 134455900
Drain Hose
★★★★★
★★★★★
(4)
PartSelect #: PS975871
Manufacturer #: 134455900
Also known as tub-to-pump drain hose.
$78.87
  In Stock
Drum Vane – Part Number: 134509600
Drum Vane
★★★★★
★★★★★
(1)
PartSelect #: PS1145727
Manufacturer #: 134509600
Sold individually.
$171.26
  In Stock
Door Glass – Part Number: 134366400
Door Glass
★★★★★
★★★★★
(4)
PartSelect #: PS1145708
Manufacturer #: 134366400
$306.09
  In Stock

Questions And Answers for FTF2140FS1

Ask our experts a question about this model and we'll get back to you as soon as possible!

5 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kent
July 7, 2021
As soon as I turn on, it dumps water all over floor.
For model number FTF2140FS1
PartSelect logo
Hello Kent, Thank you for the question. This could be several issues. We suggest checking the hoses to make sure nothing has come loose. You can also check the Drain Pump for damage that is causing a leak. Depending on where the water is coming from, you can also check the Water Vale for a leak. Thank you for your inquiry, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Sue
August 21, 2023
Hi. The washing machine front board show no lights on. Power is ok. Any fuse or breaker inside or on the control board, please? Thanks
For model number FTF2140FS1
PartSelect logo
Hi Sue, thank you for reaching out. Our research has found that it is most likely the Control Board, part number PS12724037, there is no fuse to replace on the control board. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Al
October 20, 2023
Washer will fill only on Soak cycle. What's wrong?
For model number FTF2140FS1
PartSelect logo
Hello Al, thank you for contacting us. According to our research, we would recommend checking the water inlet valve for any blockage. If this is not the issue, you may need to replace the control board, part number PS12724037, to fix the issue. Glad to be of assistance!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Hugh
February 1, 2020
The problem with my machine was not listed and that is simply that the machine will agitate, fill and drain with water but will not spin. When the spin cycle starts there is just a buzzing noise which may suggest it's the clutch but unfortunately you did not address this symptom in your q&a section, can you please advise before i start dismantling the entire machine. Thank you.
For model number FTF2140FS1
PartSelect logo
Hi Hugh. Most commonly something is stuck in the pump and blocking it. Thank you for your question and good luck with your repair.

Was this helpful?
Thank you for voting!
Related Parts:
Doreen
February 26, 2020
This washer was in a house when purchased. We are moving again, how do you remove all water for easy lifting.
For model number FTF2140FS1
PartSelect logo
Hi Doreen, thank you for your question. There should be no water inside of your machine if your machine is not in an cleaning cycle. You might want to check your drain hoses and drain pump to see if they are clogged and functioning. To remove any stuck water because it is not draining out, you may have to open up your machine and disconnect the hose to your drain pump to allow the water to flow out from your tub. You will need a bucket and towels to catch any excess water. Good luck with your repair.

Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the FTF2140FS1

[Viewing 15 of 15]
Lid or door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Locking Issues
Fixed by
these parts
Fixing Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing
Show All
Door latch failure
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Burning smell
Fixed by
these parts
Fixing
Show All
Not draining
Fixed by
these parts
Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Door Catch
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
Parts Used:
Door Strike
  • Joy from Columbia, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
564 of 581 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door on washer wouldn't lock or start
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • DOUG from KING FERRY, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
472 of 554 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Bellow Ripped
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
Parts Used:
Bellow Kit
  • Peggy from New Castle, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
247 of 340 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!