Models > GFS165

GFS165 (MN10) Caloric Refrigerator - Overview

Sections of the GFS165

[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Dryer Radiant Flame Sensor – Part Number: WP338906
Dryer Radiant Flame Sensor
★★★★★
★★★★★
(3)
PartSelect #: PS11741429
Manufacturer #: WP338906
This part senses the flame for heat allowing the gas valve to open.This flame sensor is three inches long and is used for many gas clothes dryers.This flame sensor assembly is made of both plastic and metal.
$61.09
  In Stock
Order within the next 7 hrs and your part ships today!
Igniter – Part Number: WP37001308
Igniter
PartSelect #: PS11741932
Manufacturer #: WP37001308
The bracket is no longer included.
$57.69
  In Stock
Order within the next 7 hrs and your part ships today!
Cold Control Thermostat – Part Number: 1123394
Cold Control Thermostat
★★★★★
★★★★★
(1)
PartSelect #: PS316579
Manufacturer #: 1123394
This cold control thermostat has a temperature range from 29.5 degrees Fahrenheit to 16.5 degrees Fahrenheit and a capillary length of 35 inches.
$163.77
  In Stock
Order within the next 7 hrs and your part ships today!
High Limit Thermostat – Part Number: 489P3
High Limit Thermostat
PartSelect #: PS2044484
Manufacturer #: 489P3
This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element.
  No Longer Available
IMPELLER – Part Number: 300843
IMPELLER
PartSelect #: PS72411
Manufacturer #: 300843
  No Longer Available
TIMER,230/50 – Part Number: 56531
TIMER,230/50
PartSelect #: PS100834
Manufacturer #: 56531
  No Longer Available
SWITCH,TEMPERATURE SEL – Part Number: 56576
SWITCH,TEMPERATURE SEL
PartSelect #: PS100855
Manufacturer #: 56576
  No Longer Available
SCREW,#6-20X.44/.41 IN – Part Number: 56693
SCREW,#6-20X.44/.41 IN
PartSelect #: PS100887
Manufacturer #: 56693
  No Longer Available
INSTRUCTIONS,DRYING RACK – Part Number: 56694
INSTRUCTIONS,DRYING RACK
PartSelect #: PS100888
Manufacturer #: 56694
  No Longer Available
DISCONTINUED – Part Number: 596P3
DISCONTINUED
PartSelect #: PS103102
Manufacturer #: 596P3
  No Longer Available
SWTCH-PRCT – Part Number: 314210
SWTCH-PRCT
PartSelect #: PS336591
Manufacturer #: 314210
  No Longer Available
PAD – Part Number: 56720
PAD
PartSelect #: PS515791
Manufacturer #: 56720
  No Longer Available

Questions And Answers for GFS165

Be the first to ask our experts a question about this model!

Common Symptoms of the GFS165

[Viewing 3 of 3]
Not Heating
Fixed by
these parts
Fixing
Show All
Too hot
Fixed by
these parts
Fixing
Show All
Fridge too warm
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas Flame Would Drop Out
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Parts Used:
Dryer Radiant Flame Sensor
  • FRED from BRIELLE, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
47 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat up.
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the front open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Parts Used:
Dryer Radiant Flame Sensor
  • Roger from Bonners Ferry, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
26 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dyer would not heat, flame would shut off within 10 seconds
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Parts Used:
Dryer Radiant Flame Sensor
  • Christy from Riley, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
24 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!