Models > GLEQ2152ES0

GLEQ2152ES0 Frigidaire Dryer - Overview

Sections of the GLEQ2152ES0

[Viewing 6 of 6]

Manuals & Care Guides for GLEQ2152ES0

Click to download
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
★★★★★
★★★★★
(64)
PartSelect #: PS459829
Manufacturer #: 5303281153
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$71.08
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Drum Belt – Part Number: 134503600
Drum Belt
★★★★★
★★★★★
(25)
PartSelect #: PS1148434
Manufacturer #: 134503600
This 88 3/4 inches long and 1/4 inch wide dryer drum belt goes around the dryer drum and the pulley to rotate the drum once the motor is activated.
$22.52
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Heating Element Assembly – Part Number: 131553900
Heating Element Assembly
★★★★★
★★★★★
(32)
PartSelect #: PS418120
Manufacturer #: 131553900
This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.
$216.87
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(7)
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$8.07
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Drum Glide - White – Part Number: 137513300
Drum Glide - White
★★★★★
★★★★★
(3)
PartSelect #: PS5574052
Manufacturer #: 137513300
Appliance requires 2 .Sold individually.
$44.93
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Thermal Limiter - Limit 220 – Part Number: 134120900
Thermal Limiter - Limit 220
★★★★★
★★★★★
(11)
PartSelect #: PS419402
Manufacturer #: 134120900
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.68
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Lower Front Felt Seal with Adhesive – Part Number: 5303937183
Lower Front Felt Seal with Adhesive
★★★★★
★★★★★
(9)
PartSelect #: PS832645
Manufacturer #: 5303937183
$25.32
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(4)
PartSelect #: PS418433
Manufacturer #: 131658800
This part helps keep the door closed while the machine is running.
$79.93
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Lint Filter – Part Number: 131450300
Lint Filter
★★★★★
★★★★★
(4)
PartSelect #: PS417841
Manufacturer #: 131450300
This white dryer lint filter screen collects lint as it passes through the dryer vent.
$36.36
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Door Strike – Part Number: 5303207102
Door Strike
★★★★★
★★★★★
(6)
PartSelect #: PS455020
Manufacturer #: 5303207102
"Male" piece of a dryer door closing mechanism.
$23.90
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
High Limit Thermostat – Part Number: 3204267
High Limit Thermostat
★★★★★
★★★★★
(2)
PartSelect #: PS446428
Manufacturer #: 3204267
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$119.16
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!
Blower Housing with Blower Wheel – Part Number: 131775600
Blower Housing with Blower Wheel
★★★★★
★★★★★
(10)
PartSelect #: PS418726
Manufacturer #: 131775600
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
$161.95
  In Stock
Order within the next 1 hr and 3 mins and your part ships today!

Questions And Answers for GLEQ2152ES0

Ask our experts a question about this model and we'll get back to you as soon as possible!

9 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Alexa
January 29, 2020
All the lights just are blinking randomly. I start the dryer and within 10 seconds all lights just start flashing and random beeping.
For model number GLEQ2152ES0
PartSelect logo
Hi Alexa, Thank you for your question. If the lights on the dryer are blinking randomly after you start the dryer, try unplugging the dryer for a few minutes to see if this helps reset it. If this does not help, you will need to check both the electronic control board and the heating element. Check the heating element with a multi-meter. Disconnect your dryer from the power source and locate the heating element. Depending on your model, you may need to open your dryer’s cabinet to access the heating element. Remove the heating element from the dryer and visually inspect it for signs of damage or burning. Set your multi-meter to the Rx1 setting and touch the probes to element terminals to test for continuity. If you receive a reading of infinity, you need a replacement heating element. You will need to check the electronic control board visually for signs of damage, wear or burn marks. If it shows any of these signs, it will need to be replaced. We hope this helps. Thank you and have a great day.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Timmy
August 26, 2021
Dryer starts to run then stops and has a code of "e68"
For model number GLEQ2152ES0
PartSelect logo
Hello Timmy, Thank you for the question. The error code E68 is a stuck button. We suggest checking all of the buttons to be sure nothing is stuck and working properly. If the buttons are good, the Control Board, PartSelect Number PS12724036 will need to be replaced. We hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Norm
October 11, 2021
The dryer will turn on, run for about 15 minutes, and then shut down. After shutting down, the led lights on the far right of the panel next to "drying", "cool down", "press saver", and "clean lint filter" blink on/off continuously. I have found several other people on the web with this same problem but no one has provided a solution to the problem. Any ideas? Thanks!
For model number GLEQ2152ES0
PartSelect logo
Hello Norm, Thank you for the question. This could indicate the Dryer is over heating or thinks it is over heating. We suggest to first clean out any lint build up in the Duct, Vent Hose and inside the cabinet. This can restrict the Air flow and cause over heating. If the issue continues you can test the Thermal Limiter. The reading should be close to 0 ohms if the limiter is working properly. The High Limit Thermostat will read zero ohms of resistance. We hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Terry
February 24, 2020
Dryness lights will not light. Try to select and beeps three times and displays err. Taking very long time to dry and has heat.
For model number GLEQ2152ES0
PartSelect logo
Good Day Terry. Thank you for your question in regards to your unit (Model Number GLEQ2152ES0). Based on our research, we have found the following information that may explain why you are having this issue: 1) Lint screen is clogged with lint (Solution - Make sure all lint has been removed from the dryer lint screen before starting each cycle). 2) Exhaust duct requirements have not been met (Solution - Exhaust duct must be at least 4inches in diameter and made of rigid or flexible metal). 3) Electric dryer is connected to a 208 volt circuit (Drying time will be 20% longer than drying on a 240 volt circuit). 4) Outside exhaust hood or exhaust duct may be clogged or restricted (Solution - Clean out any obstruction). We hope this helps! Best Regards.

Was this helpful?
Thank you for voting!
Betty
January 16, 2020
Why might this model be making a screeching noise when it is running? Also now having an error code 68. It has been coming in and beeping when it is off. Thank you, Betty
For model number GLEQ2152ES0
PartSelect logo
Hi Betty, Thank you for your question. The E64 error code is letting you know that there is a heater open circuit and the heating element or wiring is defective. Check heater coils and connections for open circuits. Replace heater and or wiring and retest. You will need to test the parts with a multimeter. Disconnect your dryer from the power source and locate the heating element. Depending on your model, you may need to open your dryer’s cabinet to access the heating element. Remove the heating element from the dryer and visually inspect it for signs of damage or burning. Set your multi-meter to the Rx1 setting and touch the probes to element terminals to test for continuity. If you receive a reading of infinity, you need a replacement heating element. We hope this helps. Thank you and have a great day.

Was this helpful?
Thank you for voting!
  • 1
  • 2

Common Symptoms of the GLEQ2152ES0

[Viewing 8 of 8]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Too hot
Fixed by
these parts
Fixing Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Not Heating
Fixed by
these parts
Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
334 of 351 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
short circuit with a brasier metal support
Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.

5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.

6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.

Follow the same steps backwards to put the dryer together again.
Parts Used:
Heating Element Assembly
  • Juan Carlos from Weston, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
233 of 271 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermal Limiter opened
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.
Parts Used:
Thermal Limiter - Limit 220
  • Stephen from Newnan, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
243 of 319 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!