Models > IJ41001

IJ41001 Inglis Washer - Overview

Sections of the IJ41001

[Viewing 10 of 10]

Manuals & Care Guides for IJ41001

Click to download
Keep searches simple, eg. "belt" or "pump".
Direct Drive Motor Coupling – Part Number: 285753A
Direct Drive Motor Coupling
★★★★★
★★★★★
(63)
PartSelect #: PS1485646
Manufacturer #: 285753A
This coupling kit is located between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.
$35.42
  In Stock
Direct Drive Water Pump – Part Number: WP3363394
Direct Drive Water Pump
★★★★★
★★★★★
(49)
PartSelect #: PS11741239
Manufacturer #: WP3363394
This pump is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.
$61.97
  In Stock
Suspension Spring – Part Number: WP63907
Suspension Spring
★★★★★
★★★★★
(4)
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$10.18
  In Stock
Clutch Assembly – Part Number: 285785
Clutch Assembly
★★★★★
★★★★★
(41)
PartSelect #: PS334641
Manufacturer #: 285785
A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring f...
$38.04
  In Stock
Water Inlet Valve with Mounting Bracket – Part Number: 285805
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
(29)
PartSelect #: PS334646
Manufacturer #: 285805
The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.
$44.85
  In Stock
Tub Spring – Part Number: WPW10250667
Tub Spring
★★★★★
★★★★★
(18)
PartSelect #: PS11751118
Manufacturer #: WPW10250667
This part is used to balance the tub during spin cycle. Sold individually.
$8.94
  In Stock
Lid Switch – Part Number: 3949247V
Lid Switch
★★★★★
★★★★★
(47)
PartSelect #: PS11722098
Manufacturer #: 3949247V
This is a replacement lid switch for your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
$67.19
  In Stock
Agitator Bolt – Part Number: WP358237
Agitator Bolt
★★★★★
★★★★★
(5)
PartSelect #: PS11741866
Manufacturer #: WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$8.94
  In Stock
Touch-Up Paint - White – Part Number: 72017
Touch-Up Paint - White
★★★★★
★★★★★
(16)
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.18
  In Stock
Fabric Softener Dispenser – Part Number: WP63594
Fabric Softener Dispenser
★★★★★
★★★★★
(22)
PartSelect #: PS11743341
Manufacturer #: WP63594
This parts fits on top of the agitator.
$14.89
  In Stock
Drain Hose – Part Number: WPW10358149
Drain Hose
★★★★★
★★★★★
(19)
PartSelect #: PS11753688
Manufacturer #: WPW10358149
It connects from the pump to the back panel. The clamp is not included.
$49.48
  In Stock
Tub Wear Pads - Package of 3 – Part Number: 285744
Tub Wear Pads - Package of 3
★★★★★
★★★★★
(8)
PartSelect #: PS334620
Manufacturer #: 285744
This package of pads contains three tub wear pads.
$21.41
  In Stock

Questions And Answers for IJ41001

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bev
December 19, 2019
Do you have any information on the energy consumption of this machine. We just bought a house and it came with the deal. It would be helpful to know the efficiency of it so we can decide if we should replace and to compare with other models. Thanks.
For model number IJ41001
PartSelect logo
Good Day Bev. Thank you for your question in regards to your unit (Model Number IJ41001). Unfortunately we do not have the specific information that you are looking for and would recommend reaching out to the manufacture for further assistance. Best Regards.

Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the IJ41001

[Viewing 16 of 16]
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing Fixing Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing Fixing Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing
Show All
Leaks water
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Parts Used:
Direct Drive Motor Coupling
  • Jeff from Wayne, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1099 of 1185 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pump leaking when machine used.
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. Once the machine is on it's back you remove the hose clamps with a pair of pliers and disconnect the hoses. The pump is secured to the motor with a pair of spring steel retaining clips which are easily popped off by hand. Once the clips are removed, the pump is in your hand. Put the new pump in place, replace the retaining clips and hoses, and you're done. This has to have been the easiest repair I've ever done. I wish cleaning gutters was this easy.
Parts Used:
Pump Retainer Direct Drive Water Pump
  • Tom from Granby, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
589 of 628 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spin cycle did not engage
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly
Parts Used:
Clutch Assembly
  • Andrew from SLC, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
492 of 526 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!