This is replacement vent grille or vent grill for your microwave. You will find the grill vent either above or below the microwave door, depending on your model. If your vent grill is discolored or cr...
This metal vent damper door closes off the exhaust duct when the fan is not running to stop outside air from entering the microwave unit, and opens when the fan turns on to allow air to vent away from...
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be...
This part is the replacement base plate trim, also known as the front décor for your microwave. It is gray in color and is approximately 30 inches long and 1 ½ inches wide. The base plate trim forms a...
If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed thr...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
June 7, 2023
Slide out vent you push to slide out LG I need 2 light bulbs cavity lamps
For model number LMHM2017ST
Hi Roseann, thank you for contacting us. According to our understanding, the part you are looking for is the microwave light bulb, part number PS3530415. There are two similar light bulbs on the slide-out vent in the cavities of the reflectors. This part number contains a single bulb. You may have to order two bulbs separately. If you require assistance to place an order, please contact customer service!
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far left side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Leave the unit installed. Remove 8 screws, 4 on each side of the bottom of the drawer. It is hinged on the back but front will drop down. Remove screws attached to the white slide rails but hold bezel assembly so the spring metal on each side do no break. Look in assembly from the back to front. With a long Phillips remove the screws holding the bezel on. 3 screws. Remove old Bezel. Put new on and reassemble using the reverse.