Models > LW8203W2

LW8203W2 (PLW8203W2 B) Amana Washer - Overview

Sections of the LW8203W2

[Viewing 27 of 27]
Keep searches simple, eg. "belt" or "pump".
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(5)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.43
  In Stock
Order within the next 10 hrs and your part ships today!
Thrust Washer – Part Number: WP233520
Thrust Washer
PartSelect #: PS11740482
Manufacturer #: WP233520
This washer is 3/4 inches in diameter.
$10.11
  In Stock
Order within the next 10 hrs and your part ships today!
Hose Clamp – Part Number: WP596669
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
  In Stock
Order within the next 10 hrs and your part ships today!
Hose Clamp – Part Number: WP285655
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
This hose clamp is sold individually.
$14.11
  In Stock
Order within the next 10 hrs and your part ships today!
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$6.88
  In Stock
Order within the next 10 hrs and your part ships today!
Adjustable Leveling Leg – Part Number: 22003428
Adjustable Leveling Leg
★★★★★
★★★★★
(3)
PartSelect #: PS2021026
Manufacturer #: 22003428
Sold Individually. This adjustable leveling leg comes with a stop nut.
$23.82
  In Stock
Order within the next 10 hrs and your part ships today!
Retaining Ring – Part Number: WP23748
Retaining Ring
PartSelect #: PS11740487
Manufacturer #: WP23748
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
$17.27
  In Stock
Order within the next 10 hrs and your part ships today!
Lid Hinge Mounting Screw – Part Number: WPW10119828
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.68
  In Stock
Order within the next 10 hrs and your part ships today!
Drain Pump – Part Number: 27001233
Drain Pump
PartSelect #: PS1594294
Manufacturer #: 27001233
This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.
  No Longer Available
Drain Hose with Rubber Elbow – Part Number: WP40053901
Drain Hose with Rubber Elbow
PartSelect #: PS11742254
Manufacturer #: WP40053901
This hose attaches to the pump to help remove the water out of the washer. 7 feet in length.
$74.48
  In Stock
Order within the next 10 hrs and your part ships today!
Screw – Part Number: WPY014874
Screw
PartSelect #: PS11757438
Manufacturer #: WPY014874
Sold Individually.
$10.23
  Special Order
Inlet Hose Washer – Part Number: WPY013783
Inlet Hose Washer
PartSelect #: PS11757437
Manufacturer #: WPY013783
This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.
$9.68
  Special Order

Questions And Answers for LW8203W2

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sandy
April 29, 2023
How to get the agitator out when it's stuck?
For model number LW8203W2
PartSelect logo
Hello Sandy, thank you for the great question. Use the following instructions to remove the stuck agitator: 1. Remove the dispenser cup. 2. Unthread the bolt. 3. Insert a rope under the agitator and pull it up with force. We hope this information is useful!

Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the LW8203W2

[Viewing 7 of 7]
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Noisy
Fixed by
these parts
Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Frayed V-belt
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
Parts Used:
V-Style Drive Belt (32.5 inches long)
  • John from Milton, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
60 of 67 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking on floor from "mysterious place underneath washer"
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).

Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.

So, I simply replaced the hose and turned the bracket around to the correct orientation.

Everything worked as planned and my repair cost was much less than if I had called someone out.
Parts Used:
Drain Hose with Rubber Elbow
  • Bryan from Chicago, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
50 of 55 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Seal On The Bottom Of The Tub Was Leaking
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forward. Primed the pump and started the machine for the stated time and was a sucess.
Parts Used:
Complete Hub and Seal Kit
  • HOWARD from CORTLAND, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
34 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!