Models
>
NDE2330AYW
NDE2330AYW Amana Dryer - Overview
Sections of the NDE2330AYW
[Viewing 10 of 10]Manuals & Care Guides for NDE2330AYW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Multi Rib Belt
PartSelect #: PS11742271
Manufacturer #: WP40111201
This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
$12.00
In Stock
Drum Support Roller
PartSelect #: PS11741913
Manufacturer #: WP37001042
This single drum support roller is used for square ported model clothes dryers. It has a metallic bearing in its center.
$26.63
In Stock
Door Catch Kit
PartSelect #: PS2162263
Manufacturer #: LA-1003
This kit comes in two pieces: the catch and the clip.
$41.11
In Stock
Idler Pulley Wheel with Bearing
PartSelect #: PS11757553
Manufacturer #: WPY54414
This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.
$28.32
In Stock
High Limit Thermal Fuse
PartSelect #: PS11742274
Manufacturer #: WP40113801
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
$16.48
In Stock
Door Switch Kit
PartSelect #: PS1964648
Manufacturer #: W10169313
This part replaces older two terminal switches.
$38.07
In Stock
Thrust Washer
PartSelect #: PS11740482
Manufacturer #: WP233520
This washer is 3/4 inches in diameter.
$10.11
In Stock
Cylinder Felt Seal
PartSelect #: PS11741917
Manufacturer #: WP37001132
This part is located between the back of the drum and the rear dryer panel.
$65.74
In Stock
Cylinder Glide Bracket
PartSelect #: PS11741912
Manufacturer #: WP37001036
These brackets support each side of the tub. Order quantity needed.
$82.21
In Stock
Single Drum Glide Felt Pad
PartSelect #: PS11742773
Manufacturer #: WP500121
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
$10.18
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$6.88
In Stock
Questions And Answers for NDE2330AYW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Connie
December 9, 2022
Does it have 2 belts
For model number NDE2330AYW
Hi Connie,
Thank you for your question. The dryer has one belt. The part number listed under your model number for the belt is PS11742271. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
Brad
June 26, 2023
Does this kit (WPY54414) Come with the C ring to hold the pully in place?
For model number NDE2330AYW
Hello Brad, thank you for contacting us. According to our research, the retaining ring does not come with the kit. You may need to order the retaining ring, part number PS11740487, separately. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Brad
June 26, 2023
i need the entire arm for the idler pully. But I don't see one listed. Can you help me with that?
For model number NDE2330AYW
Hello Brad, thank you for your query. The part you are looking for is the idler pulley lever and shaft, part number PS11741920. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the NDE2330AYW
[Viewing 10 of 10]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
Parts Used:
-
Chris from Hopedale, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
524 of 547 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace drive belt
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.)
Vacuumed inside of dryer (full of lint.)
Parts Used:
-
Robert from Skokie, IL
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver
304 of 354 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squeeling/Screeching
First I read all of the other stories about this problem so I would have the correct parts. At $6 a roller, decided to get all 3 & a belt. Pulled the lower panel off (2 bolts), then the door (2 bolts). Marked the door switch wires. Took 2 bolts out of the top & tilted it back. I found this the easiest way to access the drum. Mark 2 wires before disconnecting them from the top. All bolts are 5/16". Removed the plastic piece that connects the lint trap to the blower (3 screws). Have to access these from inside the drum. Removed the belt, then the drum. The bad roller was the belt tension roller. Can't get to the snap ring from the front of the dryer for this roller. The 2 rollers in the back you can get to without removing the drum completely. Very easy to replace all rollers with the drum out. Also very easy to re-assemble. Buy or borrow a good set of snap ring pliers. Make sure you diagram the proper belt route if you don't have a picture. I printed a picture off this web site. Have someone hold the drum up so you can get the belt on, otherwise the entire repair is a 1 person job. Went back together in about 10 minutes. Total cost $40.00 parts & shipping.
Parts Used:
-
William from Round Mountain, NV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Socket set
241 of 318 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!