Models > RVM1325WW02

RVM1325WW02 Hotpoint Microwave - Overview

Sections of the RVM1325WW02

[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W 130V – Part Number: WB36X10003
Light Bulb - 40W 130V
★★★★★
★★★★★
(3)
PartSelect #: PS247209
Manufacturer #: WB36X10003
This light bulb is a 40 watt, 130-volt clear appliance light bulb for your microwave. It is sold individually.
$28.05
  Special Order
Light Socket - 250V 75W – Part Number: WB08X10016
Light Socket - 250V 75W
★★★★★
★★★★★
(2)
PartSelect #: PS230544
Manufacturer #: WB08X10016
Light bulb not included.
$36.38
  Special Order
Secondary Door Switch – Part Number: WB24X829
Secondary Door Switch
★★★★★
★★★★★
(1)
PartSelect #: PS237421
Manufacturer #: WB24X829
  No Longer Available
Aluminum Grease Filter – Part Number: WB6X486
Aluminum Grease Filter
PartSelect #: PS255242
Manufacturer #: WB6X486
This aluminum filter collects grease particles in the air from cooking. Sold individually.
$53.00
  Special Order
Glass Light Lens – Part Number: WB36X10071
Glass Light Lens
PartSelect #: PS247275
Manufacturer #: WB36X10071
$24.34
  Special Order
Monitor Door Switch – Part Number: WB24X830
Monitor Door Switch
★★★★★
★★★★★
(1)
PartSelect #: PS237422
Manufacturer #: WB24X830
$47.21
  Special Order
Screw – Part Number: WE02X10086
Screw
PartSelect #: PS3511445
Manufacturer #: WE02X10086
Sold individually.
$8.25
  Special Order
Hood Damper Assembly – Part Number: WB06X10436
Hood Damper Assembly
★★★★★
★★★★★
(1)
PartSelect #: PS651224
Manufacturer #: WB06X10436
  No Longer Available
Thermal Fuse – Part Number: WB27X1127
Thermal Fuse
PartSelect #: PS239811
Manufacturer #: WB27X1127
  No Longer Available
Rectangle Glass Tray – Part Number: WB48X194
Rectangle Glass Tray
PartSelect #: PS249692
Manufacturer #: WB48X194
  No Longer Available
Tapping Screw – Part Number: WB1X1525
Tapping Screw
PartSelect #: PS234666
Manufacturer #: WB1X1525
  No Longer Available
High Voltage Diode – Part Number: WB27X1160
High Voltage Diode
PartSelect #: PS239843
Manufacturer #: WB27X1160
This diode has a 1/4" female connection and an eyelet.
  No Longer Available

Questions And Answers for RVM1325WW02

Be the first to ask our experts a question about this model!

Common Symptoms of the RVM1325WW02

[Viewing 4 of 4]
Won’t turn on
Fixed by
these parts
Fixing Fixing Fixing
Show All
Doesn’t shut off
Fixed by
these parts
Fixing Fixing
Show All
No heat
Fixed by
these parts
Fixing Fixing Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the only difficult part. First use a torx bit to remove the two torx screws below the latches inside the microwave. This frees the latching part inside, that holds the door switches, which you will remove after you take off the control panel. The top grill has to come off before you can remove the door panel. Remove the screws above the grill, on the microwave top cover, The grill on this model is covered with a panel that moves out when it vents. After removing the two top screws, the covered grill vent slides left to remove. Be careful, as the sliding tabs are plastic. Wiggle and jiggle it, to slip it off. Below the removed grill, is a small metal grill with one screw in lower center. Remove that screw, and wiggle that out. You'll then see the one screw that holds on the control panel. Remove this screw, and lift the control panel up to remove. Again, go slowly and gently, as the bottom tabs holding the control panel in, are also plastic and easily broken. Lay the control panel on something, (I used the coffee maker) and pull out the wire bundles tucked on the left, that are attached to the latching panel. Wiggle the latching panel gently to lift it up off of it's plastic tabs and pull it out towards you, so you can see the three door switches. Each switch (part number WB24X829) has a little black switch on it. Feel each switch with either your finger, or a screwdriver to see which one doesn't "click" strongly. The weak one is the one you will replace. The door switches are fitted into a tab, and plugged into their wires. Remove the defective switch, pull out the wires, and replace it with the new switch, plugging back the wires, and slipping it back into it's plastic tabs. Then put everything back together in reverse order. The entire job took me fifteen minutes EXCEPT for figuring out how to slide off the upper grill, which I have told you. A repairman would have cost $150, the part was $18. AND, there's a good chance, the other two switches will get "used up" in the next year or so as well, so I'll be ready next time. Thank you, Partselect, why work all day, to make money, only to give it to somebody else, for fifteen minutes of work. All I needed was the knowledge.
Parts Used:
Secondary Door Switch
  • Marla from Arlington, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
310 of 370 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb out, tried to remove, lamp socket broke
Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged the wires and took it out. Simply replaced socket, fastened bottom cover of microwave, installed new bulb and closed lens cover.
Parts Used:
Light Bulb - 40W 130V Light Socket - 250V 75W
  • Gene from Urbana, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
218 of 259 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bulb had broken off in base that was still screwed into socket
At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you can drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age
Parts Used:
Light Bulb - 40W 130V
  • william from san antonio, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
92 of 104 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!