Models
>
SER341AS0
SER341AS0 Westinghouse Dryer - Overview
Sections of the SER341AS0
[Viewing 6 of 6]Manuals & Care Guides for SER341AS0
Click to downloadManual
Owner's Manuals
(0.21MB)
Manual
Owner's Manuals
(0.63MB)
Care
Use and Care Manual
(0.09MB)
Wiring
Wiring Diagram
(0.26MB)
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit
PartSelect #: PS459829
Manufacturer #: 5303281153
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$79.28
In Stock
Control Knob
PartSelect #: PS418888
Manufacturer #: 131858004
Sold individually. This white knob accepts a D-shaped shaft.
$63.58
In Stock
Drum Belt
PartSelect #: PS1148434
Manufacturer #: 134503600
This 88 3/4 inches long and 1/4 inch wide dryer drum belt goes around the dryer drum and the pulley to rotate the drum once the motor is activated.
$22.44
In Stock
Upper Drum Glide
PartSelect #: PS470317
Manufacturer #: 5303937139
Front upper felt glide pad with 3 nylon glides - includes adhesive.
$51.09
In Stock
Heating Element Assembly
PartSelect #: PS418120
Manufacturer #: 131553900
This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.
$216.14
In Stock
Drum Support Bearing
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$8.04
In Stock
Thermal Limiter - Limit 220
PartSelect #: PS419402
Manufacturer #: 134120900
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.56
In Stock
Front Lower Drum Seal
PartSelect #: PS460194
Manufacturer #: 5303283286
This part helps to keep the dryer running as quietly as possible.
$53.74
On Order
Door Catch
PartSelect #: PS418433
Manufacturer #: 131658800
This part helps keep the door closed while the machine is running.
$79.66
In Stock
Lint Filter
PartSelect #: PS417841
Manufacturer #: 131450300
This white dryer lint filter screen collects lint as it passes through the dryer vent.
$36.24
In Stock
Door Strike
PartSelect #: PS455020
Manufacturer #: 5303207102
"Male" piece of a dryer door closing mechanism.
$23.90
In Stock
High Limit Thermostat
PartSelect #: PS446428
Manufacturer #: 3204267
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$119.16
In Stock
Questions And Answers for SER341AS0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the SER341AS0
[Viewing 8 of 8]Noisy
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Squealing noise
We followed the instructions for the drum glide replacement and changed the belt and drum support bearing piece, cleaned it out too. Works like a charm. Thanks for saving us a bundle.
Parts Used:
-
Cynthia from Lexington, SC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Wrench (Adjustable), Wrench set
529 of 551 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
-
Frank from Boyertown, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
334 of 353 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
short circuit with a brasier metal support
Disconect the dryer from the main power source.
1) Remove the two screws from the rear / upper panel (below the control panel).
2) Snap the front side using a flat head screw driver.
3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.
4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.
5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.
6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.
Follow the same steps backwards to put the dryer together again.
1) Remove the two screws from the rear / upper panel (below the control panel).
2) Snap the front side using a flat head screw driver.
3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.
4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.
5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.
6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.
Follow the same steps backwards to put the dryer together again.
Parts Used:
-
Juan Carlos from Weston, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
233 of 271 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!