Models > TC507B

TC507B Jenn-Air Trash Compactor - Overview

Sections of the TC507B

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
15 Inch Compactor Bags - 15 Pack – Part Number: W10165295RP
15 Inch Compactor Bags - 15 Pack
★★★★★
★★★★★
(5)
PartSelect #: PS1964579
Manufacturer #: W10165295RP
These bags will fit most 15" rectangular compactors.
$33.72
  In Stock
Order within the next 17 mins and your part ships today!
Foot, Front - Single – Part Number: WPW10001130
Foot, Front - Single
★★★★★
★★★★★
(3)
PartSelect #: PS11747965
Manufacturer #: WPW10001130
Sold Individually.
$9.50
  In Stock
Order within the next 17 mins and your part ships today!
Drive Gear Kit – Part Number: 882699
Drive Gear Kit
★★★★★
★★★★★
(10)
PartSelect #: PS398589
Manufacturer #: 882699
This kit is used for trash compactors. It includes both gears, pin spring, C-ring, ram stop, and ram cam.
$84.44
  In Stock
Order within the next 17 mins and your part ships today!
Screw – Part Number: WP489478
Screw
PartSelect #: PS11742754
Manufacturer #: WP489478
Sold individually.
$6.91
  In Stock
Order within the next 17 mins and your part ships today!
Directional Switch – Part Number: WP777811
Directional Switch
★★★★★
★★★★★
(3)
PartSelect #: PS11744742
Manufacturer #: WP777811
Used for trash compactors.
$81.80
  On Order
Range Screw – Part Number: WP3196175
Range Screw
PartSelect #: PS11740982
Manufacturer #: WP3196175
This screw is sold individually. 8-18 x 3/8
$10.26
  In Stock
Order within the next 17 mins and your part ships today!
Rotary Switch Kit – Part Number: 675382
Rotary Switch Kit
PartSelect #: PS382679
Manufacturer #: 675382
This kit comes with an on-off rotary switch and two chrome knobs.
$196.31
  Special Order
Drawer Roller – Part Number: WP9871602
Drawer Roller
★★★★★
★★★★★
(1)
PartSelect #: PS11747573
Manufacturer #: WP9871602
Appliance takes 2 - Sold individually.
$20.92
  In Stock
Order within the next 17 mins and your part ships today!
Light Switch – Part Number: WP4387911
Light Switch
★★★★★
★★★★★
(1)
PartSelect #: PS11742478
Manufacturer #: WP4387911
This part turns the light on/off as the door opens and closes.
$43.61
  In Stock
Order within the next 17 mins and your part ships today!
Power Nut Kit – Part Number: WP9870163
Power Nut Kit
★★★★★
★★★★★
(1)
PartSelect #: PS11747554
Manufacturer #: WP9870163
Includes everything pictured above.
$95.58
  In Stock
Order within the next 17 mins and your part ships today!
Handle - Black – Part Number: WP9871267
Handle - Black
PartSelect #: PS11747567
Manufacturer #: WP9871267
Screws sold separately.
$250.51
  Special Order
Foot Pedal – Part Number: 882657
Foot Pedal
PartSelect #: PS398581
Manufacturer #: 882657
$87.43
  In Stock
Order within the next 17 mins and your part ships today!

Questions And Answers for TC507B

Be the first to ask our experts a question about this model!

Common Symptoms of the TC507B

[Viewing 6 of 6]
Doesn’t stop at end of compacting cycle
Fixed by
these parts
Fixing Fixing Fixing
Show All
Compactor ram gets stuck
Fixed by
these parts
Fixing Fixing Fixing
Show All
Drawer is hard to open and or close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Won’t start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Light not working
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.
Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Parts Used:
Powerscrew Cap Drive Gear Kit Washer BEARING
  • Asbjorn from The Woodlands, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
67 of 82 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.

I took out the four screws that kept the top cover in place to expose the ram.

The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.

Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
Parts Used:
Directional Switch
  • Scott from Indianapolis, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
41 of 49 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compactor motor kept running after cycle ran, making alot of noise and unit jumping around.
Pulled the Compactor from underneath cabinet, unplugged power. Removed the top plate off compactor to expose the crush piston. Removed the front control panel by removing two phillips screws, wiring and directional (limit) switch is now exposed. Removed the two screws securing switch, removed wiring one wire at a time and replaced on new switch in same position. Replaced switch in same manner as removed, and followed reverse of above to re-assemble. Plugged back in and tested, problem resolved works like new. Only took possibly 30" to repair and saved an expensive service call.
Parts Used:
Directional Switch
  • Keith from Keller, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
33 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!