Models > WM2101HW

WM2101HW (ABWEEUS) LG Washer - Overview

Sections of the WM2101HW

[Viewing 3 of 3]

Manuals & Care Guides for WM2101HW

Click to download
Keep searches simple, eg. "belt" or "pump".
Washing Machine Drain Pump – Part Number: 4681EA2001T
Washing Machine Drain Pump
★★★★★
★★★★★
(67)
PartSelect #: PS3579318
Manufacturer #: 4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$156.41
  In Stock
Water Inlet Valve - Hot – Part Number: 5220FR2006H
Water Inlet Valve - Hot
★★★★★
★★★★★
(14)
PartSelect #: PS3527427
Manufacturer #: 5220FR2006H
$75.94
  In Stock
Door Gasket – Part Number: 4986ER0004F
Door Gasket
★★★★★
★★★★★
(5)
PartSelect #: PS3524977
Manufacturer #: 4986ER0004F
Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore ...
$196.98
  In Stock
Washer Hose with Bellows – Part Number: 4738ER1004B
Washer Hose with Bellows
★★★★★
★★★★★
(7)
PartSelect #: PS3523347
Manufacturer #: 4738ER1004B
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$62.02
  In Stock
SENSOR ASSEMBLY – Part Number: 6501KW2002B
SENSOR ASSEMBLY
★★★★★
★★★★★
(11)
PartSelect #: PS16556422
Manufacturer #: 6501KW2002B
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicate...
$62.91
  In Stock
Rear Tub Gasket – Part Number: 4036ER2004A
Rear Tub Gasket
★★★★★
★★★★★
(1)
PartSelect #: PS3522855
Manufacturer #: 4036ER2004A
$45.82
  In Stock
Door Lock Assembly – Part Number: EBF49827801
Door Lock Assembly
★★★★★
★★★★★
(3)
PartSelect #: PS3533609
Manufacturer #: EBF49827801
$109.21
  In Stock
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
Tub-to-Pump Drain Hose
★★★★★
★★★★★
(6)
PartSelect #: PS3523345
Manufacturer #: 4738ER1002A
This hose has bellows to allow for flexibility during the wash and spin cycles.
$53.20
  In Stock
Gasket – Part Number: 4036ER4001B
Gasket
PartSelect #: PS3522859
Manufacturer #: 4036ER4001B
$42.63
  In Stock
Hose Assembly,Drain – Part Number: 5215ER2002G
Hose Assembly,Drain
★★★★★
★★★★★
(2)
PartSelect #: PS3527325
Manufacturer #: 5215ER2002G
$88.40
  In Stock
Inlet Valve Assembly – Part Number: 5221ER1003A
Inlet Valve Assembly
★★★★★
★★★★★
(4)
PartSelect #: PS3527452
Manufacturer #: 5221ER1003A
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$137.96
  In Stock
Detergent Dispenser – Part Number: 3891ER2003A
Detergent Dispenser
★★★★★
★★★★★
(3)
PartSelect #: PS3522644
Manufacturer #: 3891ER2003A
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
$35.82
  In Stock

Questions And Answers for WM2101HW

Ask our experts a question about this model and we'll get back to you as soon as possible!

8 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Norris
November 30, 2019
Will not pump water out.. display shows le.. what does that code mean?
For model number WM2101HW
PartSelect logo
Hello Norris and thanks for writing. An LE error code on the washer's display indicates that the motor is locked, possibly due to a heavy wash load. Large and heavy sized loads will put a strain on the motor, causing the LE code to occur. Performing a reset on the washer will typically resolve this error with a reduced load size. We hope this helps. Please contact us anytime.

4 people found this helpful.

Was this helpful?
Thank you for voting!
Ray
March 6, 2024
Motor smell Noisey before motor code LE what should I look for next Thanks
For model number WM2101HW
PartSelect logo
Hi Ray, thank you for the question. According to our research, the LE error code indicates the motor locker error. This is an error that occurs when the motor cannot spin. We would suggest checking that there is no coin or a foreign object being caught in the mechanism. If it is fine, the issue could be with the motor stator, part number PS3522948. It works with the motor rotor to rotate the spin basket. You may need to replace it to fix the issue. We hope this solves your problem!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Duane
November 30, 2019
I need the part # for the main electric board inside the unit on the back wall for this model
For model number WM2101HW
PartSelect logo
Hello Duane and thanks for writing. It seems the part you are looking for has been discontinued for your model and is no longer available. We have no known replacement information in our system. We recommend you contact the manufacturer of the part to see if they have recently released a new substitute. We do carry other spare parts for units such as yours, for example, Part Number: PS3533609 Good Luck with your repair.

Was this helpful?
Thank you for voting!
Related Parts:
Richard
September 5, 2021
Washer seems to work good until the spin. Spins for a couple min. Then I see smoke and it smells like rubber burning. What would cause this and is it fixable
For model number WM2101HW
PartSelect logo
Hello Richard, Thank you for the question. This is normally caused by defective wiring. We suggest checking the wiring for damage or burn marks. We also suggest checking the Stator Assembly and the Rotor Position Sensor Assembly. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Kenneth
September 24, 2021
Does not totaly spin out water when done.
For model number WM2101HW
PartSelect logo
Hello Kenneth, Thank you for your inquiry. We have researched the model you have provided and we would recommend checking the following parts to fix your issue: stator assembly, rotor assembly, drain pump and motor assembly, drain hose, and the pump filter. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. Check the hoses and filter for any kinks or clogs. Good luck with your repair.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2

Common Symptoms of the WM2101HW

[Viewing 16 of 16]
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing
Show All
Draining Issues
Fixed by
these parts
Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
Engine runs but does not pump water
Fixed by
these parts
Fixing
Show All
Locking Issues
Fixed by
these parts
Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Parts Used:
Washing Machine Drain Pump
  • Jorge from Apple Valley, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
558 of 711 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Parts Used:
SENSOR ASSEMBLY
  • Mark from Harrisburg, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
236 of 308 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Parts Used:
Washing Machine Drain Pump
  • Michael from RALEIGH, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
47 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!