Models > WT1101CW

WT1101CW ((ABWEEUS)) LG Washer - Overview

Sections of the WT1101CW

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
PULSATOR ASSEMBLY – Part Number: AGZ72909711
PULSATOR ASSEMBLY
★★★★★
★★★★★
(6)
PartSelect #: PS12588963
Manufacturer #: AGZ72909711
$228.53
  In Stock
Pulsator Cap – Part Number: 5006EA3009B
Pulsator Cap
★★★★★
★★★★★
(1)
PartSelect #: PS3525704
Manufacturer #: 5006EA3009B
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$38.92
  In Stock
Washer Drain Pump Assembly – Part Number: 5859EA1004P
Washer Drain Pump Assembly
★★★★★
★★★★★
(4)
PartSelect #: PS11706439
Manufacturer #: 5859EA1004P
This drain pump is for washers. Drain pump removes water from the washer during the drain portion of the cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
$252.14
  In Stock
Clutch Housing Assembly with Mode Shifter – Part Number: AEN73131406
Clutch Housing Assembly with Mode Shifter
★★★★★
★★★★★
(1)
PartSelect #: PS11708484
Manufacturer #: AEN73131406
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive...
$331.16
  In Stock
Washer Water Inlet Valve – Part Number: AJU75152601
Washer Water Inlet Valve
★★★★★
★★★★★
(1)
PartSelect #: PS12374721
Manufacturer #: AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
$161.00
  In Stock
HOSE ASSEMBLY,DRAIN – Part Number: AEM73732901
HOSE ASSEMBLY,DRAIN
★★★★★
★★★★★
(1)
PartSelect #: PS8749199
Manufacturer #: AEM73732901
$69.53
  In Stock
HINGE – Part Number: MEF62462103
HINGE
PartSelect #: PS7795475
Manufacturer #: MEF62462103
$12.12
  In Stock
Switch Assembly,Sensor – Part Number: 6501EA1001R
Switch Assembly,Sensor
★★★★★
★★★★★
(2)
PartSelect #: PS3529177
Manufacturer #: 6501EA1001R
$71.80
  In Stock
Tub-to-Pump Hose – Part Number: AEM73213001
Tub-to-Pump Hose
★★★★★
★★★★★
(1)
PartSelect #: PS3617213
Manufacturer #: AEM73213001
$58.70
  In Stock
Suspension Assembly – Part Number: AJK72909308
Suspension Assembly
★★★★★
★★★★★
(1)
PartSelect #: PS8749609
Manufacturer #: AJK72909308
$166.27
  In Stock
Coupling – Part Number: MCJ61861201
Coupling
PartSelect #: PS3534815
Manufacturer #: MCJ61861201
$45.74
  In Stock
Bolt,Common – Part Number: 4011FA4353B
Bolt,Common
PartSelect #: PS3522804
Manufacturer #: 4011FA4353B
$10.57
  In Stock

Questions And Answers for WT1101CW

Be the first to ask our experts a question about this model!

Common Symptoms of the WT1101CW

[Viewing 8 of 8]
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
It did not drain water, cycle stops at rinse+spin.
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable supplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Parts Used:
Washer Drain Pump Assembly
  • Jesus from El Paso, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set, Wrench set
16 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
Did the repair Myself. Saved $ 400.00 in the process.
Parts Used:
Washer Water Inlet Valve
  • Flora from MIAMI, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The right side hinge that holds the washer top door broke and needed to be replaced.
Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new.
Parts Used:
HINGE
  • John from SAN JOSE, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!