This part is a replacement glass cooking tray for your microwave. The cooking tray rotates when the microwave is running, and helps your food cook evenly. As it is made of glass, these glass cooking t...
This door interlock switch is for microwaves.
Door interlock switch prevents the microwave from starting when the door is open.
Because the microwave shielding and interlock switches must be pro...
Also known as the coupler. This driver is located directly under the glass turntable, and over the motor. This part helps the glass turntable to rotate.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul
December 9, 2019
How do you take the door apart so that part #wp8206635 can be replaced
For model number YKHMS2050SS2
Hello Paul and thanks for writing.
use a Phillips head screwdriver to
unthread the two mounting screws
securing the grill with the screws
unthreaded open the oven door then slide
the grill to the left and lift it up to
remove next remove the control panel
mounting screw lift the control panel up
to detach note the orientation of the
wires connect it to the control board
then depress the locking tabs if
necessary to disconnect the wires
remove the screws securing the grounding
wire and set the control panel on a
sturdy surface release the ribbon
connector now and thread the mounting
screws securing the main control board
to the housing with the screws removed
lift out the board prepare the new
control panel for installation by
removing all of the protective coverings
make sure the new switch cable is
inserted through the hole in the control
board housing then position the board in
the housing thread the screws to secure
the ribbon connector secured the
grounding wire to the control board
housing reconnect the remaining wires to
the appropriate terminals on the board
now insert the control panel tabs into
the slots in the frame and push the
panel down replace the mounting screw to
securely insert the tabs on the grille
into the slots in the frame and slide
the grille to the right rethread the
mounting screws with the repair
completed plug the power cord back in
and your microwave oven should be ready
for use
We hope this helps. Please contact us anytime.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Garry
September 7, 2022
Hi, the touch pad keep changing display and beeps when it does. The oven still works but we have to press cancel to get the Home Screen. What part do I need?
For model number YKHMS2050SS2
Hello Garry, thank you for your question. According to our research, the issue is probably with the Touch Control Panel, part number PS11745311. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Hi Dick,
Thank you for your question. The F7 error code indicates an issue with the electronic control board. You can try to reset the microwave, by turning the circuit breaker off for 1 minute. When you turn it on, watch the microwave for 1 minute to see if the code reappears. If it does, you will need to replace the electronic control board. The part number listed under your model number for the electronic control board is PS11754101. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
There was no "fixing" per say but we still could not use the microwave without the plate. This has to be one of the biggest plates for a microwave. We ordered this through your company and we had it three days later. THREE DAYS! We had expected anywhere from 1-2 weeks. My husband was so impressed he bookmarked your site for future reference. Thank you for being so efficient and prompt. The glass turntable fit like a glove! Sincerely, Mark and Lia Hammond
By pulling the filter screens units down and out with a pair of pliers I had access to the surface lights. Pulled the lights out of their sockets and replaced the bulbs. Real easy. Since the filter units were out, replaced the filters and reinstalled the filter units. The whole operation took less than 15 minutes.
Remove the filters and use a Torx driver to remove two screws holding the motor. The wires on on the motor are held in place by a plastic clamp that must be pried open on one side. That's all it takes to replace the drive motor. Everything else that makes the turntable spin lifts off from inside the microwave.
