Part Location Diagram of 134418700 Frigidaire Agitator Drive Block
See part 2 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Agitator Drive Block

 Fits your WWS833FS1!
★★★★★
★★★★★
2 Reviews
$86.40
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your WWS833FS1!
PartSelect Number PS1152574
Manufacturer Part Number 134418700
Manufactured by Frigidaire
Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Westinghouse.
Part# 134418700 replaces these:
AP3884821, 1170670, 131475100, 134264100, 3204462, 5303306139
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
4.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 3 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Agitator Drive Block wore out
Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.

Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.

Very happy camper here!
Other Parts Used:
  • James from Somerville, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
68 of 114 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bearing and seal at top of transmission went bad causing oil from transmission to stain clothes
I removed front and top of washer to get acess to the tub. removed cap to tub along with inner tub and agitator. the hardest part is removing the springs on the bottom and tilt it forward to get tub out. removed belt, pulley and bolts holding transmission in place. reassemble using silicone grease on seals and washers. works great now
Other Parts Used:
Transmission Assembly Tub Seal Assembly
  • dave from port sanilac, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
56 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
transmission wore out
After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.
Other Parts Used:
  • Tim from Flemington, WV
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

11 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Greg
January 2, 2018
I'm wondering if this is right part to try. Washing machine seems to work fine except it won't agitate. No noises coming from it, spin cycle works, and no loud noises coming from it. I was going to replace with this part first to see if it will do the trick. What do you think?
For model number FGX831CS1
PartSelect logo
Hi Greg, Thank you for your question. The agitator block is one part that may fix the issue. If this does not work, there are some other parts that you will need to check to see which one is causing the issue. You will need to check the agitator, the belt and the motor. I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Irene
November 24, 2017
Machine spins,drain and fill up with water but it does not wash it stays filled up with water.What could be the problem?
For model number Fws933fs2
PartSelect logo
Hi Irene,Thank you for the question.Sounds like an issue with the timer,PartSelect Number PS418697.The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Tonia
January 11, 2018
Washer agitates but makes a clicking sound from the top portion of the agitator. No strange noises during rinse or spin cycle.
For model number glws1439fs0
PartSelect logo
Hi Tonia, Thank you for the question. I suggest removing the Agitator Cap and the Cap under the Agitator Cap down inside the top of the Agitator to see if the bolt needs to be tightened. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Mike
January 26, 2018
Is agitator drive block threaded inside?
PartSelect logo
Hello Mike, Thank you for your inquiry. We show that it is smooth inside. The agitator bolt goes down through this part and into the gear case shaft, which has a threaded hole in the top. Hope this helps!

Was this helpful?
Thank you for voting!
Carol
November 17, 2017
My washer fills up with water but then it stops when i move knob to rinse it spins and drains fine. Thank you
For model number FEX831CSO
PartSelect logo
Hi Carol, Thank you for your inquiry. If your timer is not advancing after the washer has filled with water, There are some parts that you will need to check to see which one is causing the issue. You will need to check the timer, the timer knob, the washer lid lock with external safety switch, the water level switch, the drain pump and the water inlet valve. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Helen
December 3, 2018
Machine works fine but on spin after motor shuts off makes loud rubbing noise. What part will fix?
For model number GLWS1349AS1
PartSelect logo
Hi Helen, thank you for your question. There are a few parts that could cause the issue but I would suggest first looking at your drive belt and your idler pulley. I hope that helps. Good luck with your repair.

Was this helpful?
Thank you for voting!
Everton
December 19, 2019
Do you have a video to replace this part, part number PS1152574?
For model number PS1152574
PartSelect logo
Hi Everton, Thank you for your question. We do not have a video related to this part, but there are videos on YouTube that you may reference that may help you install it. If you go to YouTube and type in, "How do I install an agitator drive block?", videos will come up for you. There is also installation information listed with the part on our website that you may also use to install the part. You will find this part underneath the dispenser cover and cup. You will need a 1/2-inch socket to remove the agitator bolt and then simply lift off the agitator. This may require some effort to lift off. Use a flat-head screwdriver to remove the old drive block and then push the new one into place with firmness. We hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Sascha
July 9, 2021
My washer machine makes a noise from the top agitator block it moves back and forth making a medal click click click as it agitated. I have it torn apart at the moment. Looked at the bearing after removing the outer drum and that was ok. Replacing the belt, snubber and idler pulley because the belt is damaged and the pully is hairline cracked. Of course the nut didn’t come out for the inner tub so I had to cut that off unfortunately the other side wouldn’t slide up either it was corroded to the shaft with bolts stuck inside so I get to replace the bolts, seal, and the trunnion however if I'm this in to it how do I get the sound from the agitator block to be more quiet?
For model number 41797922701
PartSelect logo
Hello Sascha, Thank you for the question. This could be the agitator being stripped and not holding the bolt properly. The Agitator will need to be replaced. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Jonathan
July 19, 2021
I have play when moving the agitator drive block back and forth and this play is not just between the drive block and transmission shaft but seems to be in the transmission itself. The reason i'm checking this part is my machine recently starting making a thud sound every time it oscillating back and forth during washing. I think this play is making this sound. Does this make sense?
For model number GLWS1339CS1
PartSelect logo
Hi Jonathan, Thank you for your question. Based on your description, the transmission is likely causing this issue, but you should also check the tub bearing as well as it may be worn. We hope this helps! Good luck with the repair!

Was this helpful?
Thank you for voting!
Jonathan
July 23, 2021
My washer won’t agitate. It fills and then doesn’t move to agitate. If i turn the timer to drain and spin it spins. I have replaced the timer, the drain pump, and even the motor. My question is i have inspected the drive block and it is on tight and not stripped. It doesn’t make a sound or movement like the motor is even trying to engage the agitation cycle. When i grab the drive block while it spins i can hold it. I have no idea what it could be.
For model number 417.40412702
PartSelect logo
Hi Jonathan, Thank you for your question. If your washer will not agitate, there are some parts that you will need to check to see which one is causing the issue. You will need to check the shock absorbers, the drive belt, the door lock and switch assembly and the door strike . We hope this helps! Good luck with the repair!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1152574
Manufacturer Part Number: 134418700
Brand
Model Number
Description
Kenmore
41789980100
Washer Dryer Combo
Kenmore
41789980800
Washer Dryer Combo
Kenmore
41790802990
Washer Dryer Combo
Kenmore
41790802991
Washer Dryer Combo
Kenmore
41790802992
Washer Dryer Combo
Kenmore
41790807990
Washer Dryer Combo
Kenmore
41790812990
Washer Dryer Combo
Kenmore
41790812991
Washer Dryer Combo
Kenmore
41790812992
Washer Dryer Combo
Kenmore
41790814000
Washer Dryer Combo
Kenmore
41790814001
Washer Dryer Combo
Kenmore
41790814002
Washer Dryer Combo
Kenmore
41790817990
Washer Dryer Combo
Kenmore
41790862990
Washer Dryer Combo
Kenmore
41790862991
Washer Dryer Combo
Kenmore
41790862992
Washer Dryer Combo
Kenmore
41790872990
Washer Dryer Combo
Kenmore
41790872991
Washer Dryer Combo
Kenmore
41790872992
Washer Dryer Combo
Kenmore
41791702000
Washer Dryer Combo
Kenmore
41791702001
Washer Dryer Combo
Kenmore
41792702200
Washer Dryer Combo
Kenmore
41793702200
Washer Dryer Combo
Kenmore
41793702201
Washer Dryer Combo
Kenmore
41793802200
Washer Dryer Combo
Kenmore
41793802201
Washer Dryer Combo
Kenmore
41793812200
Washer Dryer Combo
Kenmore
41793812201
Washer Dryer Combo
Kenmore
41793814200
Washer Dryer Combo
Kenmore
41793814201
Washer Dryer Combo
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service