Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Mary Louise L - July 27, 2023
Verified Purchase
Did the job!
We have a Maytag fridge model RSD22A 21.8 cu ft capacity which came with wheels when we purchased it in 1990 and these replacement wheels were a little too wide so we sawed off about 3/8 inches from one side of each wheel and they fit perfectly.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 5 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Left front plastic wheel was broken
Pop loose the plastic grate at the bottom.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
The plastic wheel broke in half at the right front of the refrigerator.
The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.
Other Parts Used:
Ralph from Camillus, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken front wheel
remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job
Other Parts Used:
Robert from Orting, WA
Difficulty Level:
Difficult
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
6 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken roller
proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.
Ice maker was over flowing filling the freezer with water and ice.
As per suggestion I replaced the water inlet valve. I pulled out the refrigerator and removed the cardboard panel. I removed the water inlet unit by removing two screws. I used pliers to take off the the tubes to the ice maker and the water. Then removed the inlet supply tube. Installation was the reverse process.
However this did not fix the problem. After further research on another web site, I realized that the diagram that was furnished by PartSelect did not fit my refrigerator. What I really needed was the ice maker module. So I need to order the right one and I can't return the wrong part because I installed it. So I just left the lever in the ice maker in the up postion. the ice maker is still not working.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Darlene
July 9, 2019
What are the dimensions ? I need replacement for back wheel. Thanks
For model number gx5shdxtq00
Hello Darlene, thank you for writing. This Single Roller is approximately 1.15" x 2" and is the correct replacement for your model.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Marc
January 15, 2019
Wheel is held on with a press fitted flanged at one end bolt. I don’t see how i can get it off.
Hello Marc, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
Was this helpful?
Thank you for voting!
William
July 6, 2021
Will these fit my Kenmore refrigerator
For model number 59672003014
Hello William, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS11755876 for the Left Roller and PartSelect Number: PS11755875 for the Right Roller. We hope this helps!
Hello! The front wheel on the bottom of my Amana BR22TW fridge cracked and I would like to replace it. Is PS11738235 a suitable replacement part? If not, can you please help me find a suitable replacement?
Thanks!
Vega
For model number Amana BR22TW
Hello Vega, thank you for the great question. Yes, the part you have mentioned is a compatible replacement front wheel for your model. We hope this solves your problem!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738235
Manufacturer Part Number: WP10450603
