Part Location Diagram of WP22002360 Whirlpool Water Inlet Valve
See part 7 in the diagram
Replacing your Maytag Washer Water Inlet Valve
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Water Inlet Valve

★★★★★
★★★★★
4 Reviews
$166.65
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11739359
Manufacturer Part Number WP22002360
Manufactured by Whirlpool
Product Description

Water Inlet Valve Specifications

This washing machine water inlet valve has two ports for water to enter. It comes with its own anti syphon and wire guide.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Maytag Washer Water Inlet Valve

Replacing your Maytag Washer Water Inlet Valve
Troubleshooting
This part fixes the following symptoms:
Leaking | No hot or cold water
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag.
Part# WP22002360 replaces these:
AP6006289, 22002360
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
4.0
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.1 / 5.0, 15 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
machine very slow filling with water
After making sure the lines and screens are clean, and there is good water flow thru the hoses to the valves, and there is power to the valve solenoids, (which can be detected by setting to fill and pulling out on the start knob), and hearing a "click" at the valve, you can summize that the valve is weak, or partially blocked internally.
Replace the valve by unpluging the power cord to the machine. Remove the hoses. Remove the screw that attaches the valve mounting plate. Pull the plate and valve out and remove the screw that attaches the valve to the plate. Unplug the wires from the solenoides,[IMPORTANT] noting which wires go to each valve. Remove the rubber hose on top of the valve by squeezing the hose clamp with a pair of pliers, and sliding the clamp up the hose. Now you can pull the hose off. Install the new valve in the reverse order.
Other Parts Used:
  • William from McLeansboro, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
43 of 49 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water inflow did not stop = flooded utility room
Cleaned up a wet utility room floor!

Unplugged power cord to the machine and turned off hot and cold water at the stop valves.
Removed the top machine screw that holds the metal panel with the valve attached (on the rear of the machine where hoses attach), removed it from the machine with valve and hoses attached.
Disconnected both water hoses at the old valve, together with the 1/2" hose to the machine. Mark hot and cold positions.
Moved the electrical contacts one-by-one to the new valve.
Changed the old valve for the new valve (one screw attaches to plate).
Connected the inlet hoses and 1/2" hose to the new valve, making sure hot/cold on correct positions.
Replaced plate in the machine and secured with the machine screw.

*** NO MORE WADING SINCE REPAIR *****
Other Parts Used:
  • Kevin from Chico, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
23 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer tub would fill with water when not in use and hot water would fill slowly when in use
I turned off the water at the main water inlet. I then removed the hose connections to the valve inlet. I removed the one screw on the plate pulling allowing me to pull the plate out from the washer body. I then removed the wires connected to the old valve placing them on the new valve (so not to be confused). I took off the small hose clamp attached to the valve. I removed the valve from the plate and attached the new valve placing the a new hose lamp on the hose (wires were already attached) screwed back to the plate in the washer body connecting the water lines and turned the water on at the main valve. I did have to run to the hardware store for the small hose clamp but that was my choice to replace the one that was existing. The washer now works like it is new.
Other Parts Used:
  • David from Universal City, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
H and C water valve on Maytag washer
Unhooked H and C water lines. Removed cover plate with control valves. Pulled power wires off solenoid valves. Remove exit water hose clamp then hose. Put new valves on in reverse process. Checked washer through cycle to see it worked all OK. Had to make new mount ro install valves.
Other Parts Used:
  • Charles from SIDNEY, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Only a trickle from cold water
Unscrew the hoses. Remove access panel. Unclip the 4 electrical wires. Undo the hose clamp on the top of valve and remove hose. Unscrew the one screw holding the valve in place. Remove valve. Reverse for installation.
Other Parts Used:
  • Andrew from Bennington, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Hot Water
I checked out the reason why it was not providing hot water then went to this site and found out that it was most likely a water intake valve. I am hardly a do-it-yourselfer, but after watching the "how to" video, I figured why not? The valve arrived in two days, and it was quite easy to do. We now have hot water again.
Other Parts Used:
  • Kenn from Oshkosh, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water would accumulate in the drum when not in use.If you didn't remove the washed items immediately, they would absorb water. The new valve solved the problem.
Unplug the washing machine , disconnect the water hoses, and remove two screws. Then remove the bracket and valve from its area. Remove the electrical connections and the small hose, and then reverse the procedures with the new water valve.Plug the washing machine electrical cord in , and hopefully savor the positive results.
Other Parts Used:
  • Royal from Elgin, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was overfilling.
1. Disconnected washer from power outlet.
2. Slid washer out from wall to allow access to rear.
3. Isolated water supply and removed both hot and cold water supply hoses from solenoid valve assembly.
4. Removed one screw holding angled metal bracket with water solenoid valves attached.
5. Rotated bracket to get it to clear back of washer and expose wiring and fill hose.
6. Removed hose clamp on fill hose with pliers and then removed hose from valve assembly..
7. Removed wires from each solenoid.
8. Removed one screw that attaches solenoid valve assembly to angled metal bracket.
9. Slid valve assembly to allow it to be released from angled metal bracket.
10. Reversed procedure to install new valve assembly.
Other Parts Used:
  • Glenn from Lewisport, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking Water inlet valve
Received the part in two days. Very easy instalation as the part is the exact replacement.
Other Parts Used:
  • Charles from Lewisburg, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cold water would not shut off.
Take off door at valve which holds valve in place removed with three screws. Replace valve rehook hoses easy.
Other Parts Used:
  • Paula from Essex, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

3 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom
October 28, 2017
Water drips into tub after cycle is complete. What part do i need?
For model number LAT9416AAE
PartSelect logo
Hi Tom, Thank you for your inquiry. If you washer is filling with water after the cycle has stopped there may be an issue with the water inlet valve. The Water Inlet Valve on your washing machine is used to fill the tub with cold, warm or hot water for the wash and rinse cycles. The valve is operated by electric solenoids that are controlled by the timer or electronic control board and the water level control/water level selector switch or pressure switch. If your washer continues to fill during a cycle, the water inlet valve could be at fault. To verify that the valve is at fault, unplug the washer when the symptom occurs. If the washer continues to fill, then the water inlet valve is defective. If the washer stops filling, then the problem is related to the electrical circuit that controls the valve. I hope this helps. Thank you and have a great day!

12 people found this helpful.

Was this helpful?
Thank you for voting!
Anna
April 22, 2018
Do i need to buy the whole kit or can i replace just the metal screens? I’f so how do i change those?
For model number LAT2600AAE
PartSelect logo
Hello Anna, Thank you for your inquiry. The metal screens are sold separately for your model, the part number is WP96160. Remove the fill hoses from the back of the washer with a pair of pliers, you may want to put a towel down to catch any water. You also may want to label the hoses so you don't get the hot and cold water hoses mixed up. Use a flat head screw driver to remove the old screens from the water inlet valve. Line up the new screen with the opening on the water inlet valve, and get it started inside the opening. Then carefully use a pair of needle nose pliers to gently push both sides of the screen into place. Use a flat head screw driver to make sure that the new screen is firmly in place. You can now replace the fill hoses. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Mark
March 12, 2018
Hi, would a defective water valve cause the washer to stop before going into the rinse and spin portions of the cycle? My washer needs to be manually set to continue with the rinse and spin have to be set manually. You can hear the washer making a ring sound as if its waiting for something to activate so it can continue on. I replaced the timer, but it continues to do the same thing. Any feedback will be greatly appreciated
For model number LAT9360AAE
PartSelect logo
Hello Mark, Thank you for your inquiry. It can be one of the causes. We would also recommend checking the lid switch, and the brake assembly as well. Hope this helps!

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11739359
Manufacturer Part Number: WP22002360
Brand
Model Number
Description
Maytag
LAT1916AAE
Washer - Residential
Maytag
LAT2200AAE
Washer - Residential
Maytag
LAT2300AAE
Washer - Residential
Maytag
LAT2300AWW
Washer - Residential
Maytag
LAT2301AAE
Washer - Residential
Maytag
LAT2500AAE
Washer - Residential
Maytag
LAT2600AAE
Washer - Residential
Maytag
LAT2916AAE
Washer - Residential
Maytag
LAT2916AAM
Washer - Residential
Maytag
LAT3500AAE
Washer - Residential
Maytag
LAT3500AAQ
Washer - Residential
Maytag
LAT3600AAE
Washer - Residential
Maytag
LAT3600AAQ
Washer - Residential
Maytag
LAT4916AAE
Washer - Residential
Maytag
LAT4916AAM
Washer - Residential
Maytag
LAT4916ABE
Washer - Residential
Maytag
LAT5006AAE
Washer - Residential
Maytag
LAT5916AAE
Washer - Residential
Maytag
LAT5916AAM
Washer - Residential
Maytag
LAT5916ABE
Washer - Residential
Maytag
LAT7306AAE
Washer - Residential
Maytag
LAT8006AAE
Washer - Residential
Maytag
LAT8006AAM
Washer - Residential
Maytag
LAT8016AAE
Washer - Residential
Maytag
LAT8026AAE
Washer - Residential
Maytag
LAT8026AAM
Washer - Residential
Maytag
LAT8026ABE
Washer - Residential
Maytag
LAT8106AAE
Washer - Residential
Maytag
LAT8206AAE
Washer - Residential
Maytag
LAT8206AAM
Washer - Residential
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service