Part Location Diagram of WP302868 Whirlpool Screw - 8-18 x 1/2
See part 36 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Screw - 8-18 x 1/2

 Fits your RUD3000DQ1!
$9.96
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your RUD3000DQ1!
PartSelect Number PS11740645
Manufacturer Part Number WP302868
Manufactured by Whirlpool
Product Description

Screw - 8-18 x 1/2 Specifications

Sold Individually.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Dishwasher, Trash Compactor, Range.
This part works with the following products:
Kenmore, Whirlpool, KitchenAid, Maytag.
Part# WP302868 replaces these:
AP6007528, 302868, 4163451, 776156, 780138, 816756, 977976
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.0 / 5.0, 5 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Wanted to change beige dishwasher front to black.
First , I went outside and turned the breaker for the dishwasher off. Next,I removed the screws that held the bottom 2 pieces, that rest on the floo,r in place. Then removed the two beige metal pcs. . Next I replaced them with the 2 black pieces I had ordered and secured them with the 2 black screws I had received as part of my order. Then I removed the scews from the inside of the door of my KitchenAid Dishwasher. This released both the front bottom panel and the control panel. . I took the beige bottom door panel off and moved the insulation piece from the back of thebeige panel to the back of the black panel. Then I intalled the new black panel I ordered and resecured it with two screws until I had finished with the control panel switch out.
I had to unplug an electronic tape from the inside of the beige control panel and plug the same tape back into the black control panel. I also had to remove the beige handle that was on the inside of the control panel, attached to the door, and replace it with the new black one I'd received. I then installed the black control panel and reattached it with screws and finished replacing the rest of the screws I had removed from the inside of the door.
I tested the handle to make sure it opened the door and locked it like it should and then went outside and turned the breaker back on. Came in and turned on the dishwasher and did a load of dishes. It looks awesome, matches the rest of my black appliances and I am very proud to have done it myself. I also wanted to thank the customer service lady who was so great to work with on the phone. I would shop with you again.
Other Parts Used:
Front Panel - Black ACCESS PANEL (BLACK) Control Panel Assembly - Black Kickplate - Black Door Handle
  • Margaret from San Diego, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
13 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Air Inlet was damaged and needed to be replaced.
I followed the instructions on a PartSelect U-Tube video showing how to replace the air inlet. It took me two attempts on two different days because the instructions for removing the 5 screws holding the air inlet in place were over-simplified. Accessing the screws was much more difficult than was demonstrated in the video.

On day 1 I followed the instructions for removing the door panel to gain access, but, after many failed attempts to get the nut driver properly seated on the screw heads holding the air inlet to the door, I replaced the panel so the dishwasher could be used until I found a solution to the problem.

After doing online research, I discovered a nut driver with a flexible shaft; it looked like it would allow me to properly seat the nut driver on the screw heads. Next day, I was able to replace the air inlet with no problem. It took me a little over an hour from start to finish. Aligning the holes of the new air inlet with the holes on the door so it could be screwed in place was awkward and time consuming but persistence worked.
Other Parts Used:
Air Inlet
  • Peter Del from BRISTOL, CT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Relocating dishwasher into the new kitchen layout
In this case the dishwasher had already been installed for a few years. After removing it, we inspected it and saw it needed a bit of TLC. The transport wheels on the back were missing, making it harder to move around without scratching the tile and some of the original hardware was rusted or broken off. I looked up the parts easily here on PartsSelect using their parts breakdown diagrams and was glad to see what I needed was still available. We had a licensed plumber relocate the hot water line and drain for us to make things a bit easier.
A licensed electrician had also moved the power line over to the new location and left a wire sticking out of the bottom of the wall to hardwire the dishwasher in again. We decided to convert the dishwasher to be able to be plugged into a standard 20amp wall outlet instead. We had already purchased a kit with a nice long cord and strain-relief snap on plastic fitting that snapped onto the metal incoming power box on the bottom front of the dishwasher. Using the supplied wire nuts, etc., we connected the wires and ground wire to the proper wires from the dishwasher and ground lug. We put the dishwasher aside and then went to work on converting the power wire coming out of the bottom of the wall, to a conventional outlet. I am mentioning all this because in our first attempt we unfortunately put the receptacle a bit high off the floor and the new power cord plug end, stuck out and hit the back of the dishwasher so it would not go all the way in and was sticking out from under the counter top. I tried using one of those flat adapter cables, but even that still stuck out to far. So we ended up relocating the outlet box as low as we could on the wall and this allowed the plug to stick out into the opening area at the bottom rear area of the dishwasher so it could now be slid all the way in under the kitchen counter properly. I hope that bit of trial and error will save you some time if you ever decide to go the pluggable route too.
The new installation required the use of the dishwasher side mount brackets, so we had to purchase a replacement set of those, complete with the hardware to screw them down.

This project took a bit longer than planned due to the power plug problem, one which we will remember for any other similar appliance relocation projects, as well as the time to get our new parts in that we had to order, but other than that the rest went smoothly and the dishwasher was relocated successfully.
Other Parts Used:
Screw Dishwasher Transport Wheel Cover Screw Retainer
  • Curtis from PALM BAY, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plate was missing at the time we purchased the house.
It was ok but screw holes were not in the right spot but we put one in and that is sufficient for now. It prevent thing from follow under it.
Other Parts Used:
Kickplate - Black Clip
  • Barbara from NEWPORT NEWS, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Other Parts Used:
  • Johnny from LEVITTOWN, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chris
August 21, 2019
I need a screw to hold the bottom panel of the dishwasher. The screw I have is a Flathead plastic screw but the one in the diagram is not like that. Will that screw work?
For model number MDB4949SNZ0
PartSelect logo
Hello Chris, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11740645. Hope this helps!

Was this helpful?
Thank you for voting!
Chris Harnett
August 21, 2019
I need this pop in screw for model mdb4949shz0. Your website says it doesn't exist. I got this off label on the inside of the dishwasher. What is up with that? And none of the dishwashers have what i need. I could attach a picture if there was a way? I am not a happy camper.Chris harnett
For model number MDB4949SHZ0
PartSelect logo
Hello Chris, thank you for writing. After researching your model number, I was able to confirm that this Screw part number PS11740645 is a compatible replacement for it. Good luck with your repair!

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11740645
Manufacturer Part Number: WP302868
Brand
Model Number
Description
Kenmore
110723120
Dishwasher
Kenmore
110773811
Dishwasher
Kenmore
110773812
Dishwasher
Kenmore
110773813
Dishwasher
Kenmore
110773881
Dishwasher
Kenmore
110773882
Dishwasher
Kenmore
110773883
Dishwasher
Kenmore
19385
Dishwasher - Kenmore Dishwasher Model 19385 (1988) (19385(1988)) Parts
Kenmore
19585
Dishwasher - Kenmore Dishwasher Model 19585 (1988) (19585(1988)) Parts
Kenmore
19985
Dishwasher - Kenmore Dishwasher Model 19985 (1988) (19985(1988)) Parts
Kenmore
2213222N414
Dishwasher - Kenmore Dishwasher 2213222n414
Kenmore
2213223N414
Dishwasher - Kenmore Dishwasher 2213223n414
Kenmore
2213229N414
Dishwasher - Kenmore Dishwasher 2213229n414
Kenmore
2214523N611
Dishwasher - Kenmore Dishwasher 2214523n611
Kenmore
2214715N710
Dishwasher - Kenmore Dishwasher 2214715n710
Kenmore
2214792N512
Dishwasher - Kenmore Dishwasher 2214792n512
Kenmore
2214793N512
Dishwasher - Kenmore Dishwasher 2214793n512
KitchenAid
4KUCC150S0
Trash Compactor
KitchenAid
4KUCC150S1
Trash Compactor
KitchenAid
4KUCC150S2
Trash Compactor
KitchenAid
4KUCC151T0
Trash Compactor
KitchenAid
4KUCC151T1
Trash Compactor
Kenmore
6221338550
Trash Compactor
Kenmore
6221388550
Trash Compactor
Kenmore
6228416001GO
Trash Compactor
Kenmore
62284169900
Trash Compactor
Kenmore
665110739120
Dishwasher
Kenmore
665110739130
Dishwasher
Kenmore
665110739140
Dishwasher
Kenmore
665110739190
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service