Part Location Diagram of WP3185804 Whirlpool Spark Electrode
See part 3 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Spark Electrode

 Fits your RST399UL!
★★★★★
★★★★★
2 Reviews
$62.48
  Special Order
 Fits your RST399UL!
PartSelect Number PS11740866
Manufacturer Part Number WP3185804
Manufactured by Whirlpool
Product Description

Spark Electrode Specifications

This part helps your burner ignite and produce flame.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Gas igniter glows | but will not light | Element will not heat
This part works with the following products:
Range, Cooktop.
This part works with the following products:
Amana, KitchenAid, Caloric, Whirlpool.
Part# WP3185804 replaces these:
10312601, 30935805, 3185804, 4363540, R0709508, Y0304357, Y0305975, Y0309346, Y0309358
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
4.5
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 5 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Other Parts Used:
  • Billy from Martinsville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
23 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Other Parts Used:
  • Joe from San Bruno, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
15 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spark Ignition Electrode was not sparking properly
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade
Other Parts Used:
  • Wade from Jacksons Gap, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
igniter on top right front burner was shorting out,it would click but not ignite burner
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Other Parts Used:
  • Shelly J from KAPLAN, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stove gas burner would not light?
TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.
Other Parts Used:
  • Robert from Hendersonville, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

4 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
October 27, 2017
All stove burners will not light or spark. Is it the igniter switch assembly, or spark module?How to take the top off? Is it from the back side.
For model number KGRT507FAL1
PartSelect logo
Hi Joe, Thank you for the question.To check the switch assembly you need to turn the gas off to range and with valve open check for continuity on the switches. If there is continuity then check the wiring to the spark module for broken or damaged wires. If they are good then replace the spark module. To replace the module, Turn off the gas supply and disconnect power to the range. Open the oven door and remove the racks from the oven.Next pull the range out so that you can access the back of the unit. Then remove the left side panel. To remove the spark module you need to disconnect the wire connectors from the module terminals. Then remove the mounting screw. Slide the module out from under the tab, and remove it from the housing. Reverse the steps to reinstall. To replace the switches,Turn off the gas supply and disconnect power to the range. You will need to remove the burner grates and the burner assembly's, they just lift off. Remove the two screws at each burner hole to disconnect the burner tubs. On the side panels use a flat head screw driver to pry up to release the retaining clips. Slowly lift the top watching you to not pull or damage any wires. You will need a piece of wood or something to support the top and keep it propped open. Next remove the knobs from the control panel and remove the two screws at each of of the panel and the two screws on the bottom of the panel, and pull the panel straight off. You will be able to see the switch assembly. The switches just pull off the valve shaft. Follow the red and black wire to the back corner of the stove. Disconnect the red wire from the module and the black from a plastic connector, You will just need to squeeze and pull them apart. Next remove the wires from the hook clips holding them to the side of the appliance.The reverse the steps to reinstall the new switch harness. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Carolyn
May 1, 2019
None of my burners will light without a match, and they used to. What part number do i need to order?
For model number KGCT365A
PartSelect logo
Hello Carolyn, Thank you for the question. If all of the burners have stopped operating at the same time, I suggest replacing the Spark Module, PartSelect Number PS11742616. This spark module uses a high voltage spark discharge to the switch to ingnite the gas for the cooktop burners. Thank you for your inquiry, good luck with this repair!

Was this helpful?
Thank you for voting!
Related Parts:
Carolyn
May 1, 2019
I am not sure if they all stopped at once or not. If they didn't should i still order ps11742616 spark module or something else? Thanks
For model number KGCT365A
PartSelect logo
Hello Carolyn, Thank you for contacting us. You can test the module with a multi meter to see if it has continuity as well before replacing. Hope this helps!

Was this helpful?
Thank you for voting!
Dennis
January 18, 2022
Front burner will not light by itself. I have to turn on the back burner and the front burner and then they both will turn on. Please advise. Thank You
For model number KGST307FBL
PartSelect logo
Hello Dennis, Thank you for the question. This is normally an indication the Spark Electrode is faulty and should be replaced. This part helps your burner ignite and produce flame. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11740866
Manufacturer Part Number: WP3185804
Brand
Model Number
Description
Amana
AGC585E
Range
Amana
AGC585E P1142922N
Range - Amana Range/Stove/Oven Model AGC585E P1142922N (AGC585EP1142922N) Parts
Amana
AGC585E P1143082N
Range - Amana Range/Stove/Oven Model AGC585E P1143082N (AGC585EP1143082N) Parts
Amana
AGC585E P1143131N
Range - Amana Range/Stove/Oven Model AGC585E P1143131N (AGC585EP1143131N) Parts
Amana
AGC585EP1142922N
Range - Amana Range/Stove/Oven Model AGC585EP1142922N Parts
Amana
AGC585EP1143082N
Range - Amana Range/Stove/Oven Model AGC585EP1143082N Parts
Amana
AGC585EP1143131N
Range - Amana Range/Stove/Oven Model AGC585EP1143131N Parts
Amana
AGC585LL
Range
Amana
AGC585LL P1143112N
Range - Amana Range/Stove/Oven Model AGC585LL P1143112N (AGC585LLP1143112N) Parts
Amana
AGC585LL P1143112NLL
Range - Amana Range/Stove/Oven Model AGC585LL P1143112NLL (AGC585LLP1143112NLL) Parts
Amana
AGC585LL P1143131N
Range - Amana Range/Stove/Oven Model AGC585LL P1143131N (AGC585LLP1143131N) Parts
Amana
AGC585LL P1143131NLL
Range - Amana Range/Stove/Oven Model AGC585LL P1143131NLL (AGC585LLP1143131NLL) Parts
Amana
AGC585LL P1143194NLL
Range - Amana Range/Stove/Oven Model AGC585LL P1143194NLL (AGC585LLP1143194NLL) Parts
Amana
AGC585LLP1143112N
Range - Amana Range/Stove/Oven Model AGC585LLP1143112N Parts
Amana
AGC585LLP1143112NLL
Range - Amana Range/Stove/Oven Model AGC585LLP1143112NLL Parts
Amana
AGC585LLP1143131N
Range - Amana Range/Stove/Oven Model AGC585LLP1143131N Parts
Amana
AGC585LLP1143131NLL
Range - Amana Range/Stove/Oven Model AGC585LLP1143131NLL Parts
Amana
AGC585LLP1143194NLL
Range - Amana Range/Stove/Oven Model AGC585LLP1143194NLL Parts
Amana
AGC585WW
Range
Amana
AGC585WW P1142922N
Range - Amana Range/Stove/Oven Model AGC585WW P1142922N (AGC585WWP1142922N) Parts
Amana
AGC585WW P1142922NWW
Range - Amana Range/Stove/Oven Model AGC585WW P1142922NWW (AGC585WWP1142922NWW) Parts
Amana
AGC585WW P1142925N
Range - Amana Range/Stove/Oven Model AGC585WW P1142925N (AGC585WWP1142925N) Parts
Amana
AGC585WW P1142925NWW
Range - Amana Range/Stove/Oven Model AGC585WW P1142925NWW (AGC585WWP1142925NWW) Parts
Amana
AGC585WW P1143082N
Range - Amana Range/Stove/Oven Model AGC585WW P1143082N (AGC585WWP1143082N) Parts
Amana
AGC585WW P1143082NWW
Range - Amana Range/Stove/Oven Model AGC585WW P1143082NWW (AGC585WWP1143082NWW) Parts
Amana
AGC585WW P1143127N
Range - Amana Range/Stove/Oven Model AGC585WW P1143127N (AGC585WWP1143127N) Parts
Amana
AGC585WW P1143127NWW
Range - Amana Range/Stove/Oven Model AGC585WW P1143127NWW (AGC585WWP1143127NWW) Parts
Amana
AGC585WW P1143131N
Range - Amana Range/Stove/Oven Model AGC585WW P1143131N (AGC585WWP1143131N) Parts
Amana
AGC585WW P1143131NWW
Range - Amana Range/Stove/Oven Model AGC585WW P1143131NWW (AGC585WWP1143131NWW) Parts
Amana
AGC585WW P1143194NWW
Range - Amana Range/Stove/Oven Model AGC585WW P1143194NWW (AGC585WWP1143194NWW) Parts
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service