Product Description
Door Hinge - Left or Right side Specifications
Use for painted door only. Sold individually.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Door won’t close
This part works with the following products:
Range.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Estate.
Part# WP8053807 replaces these:
AP6011640, 3186068, 8053807
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Larry B - October 28, 2022
Verified Purchase
Easy repair, perfect fit!
I've purchased many parts from this site. Everything comes exactly as ordered and usually very quickly. As long as we have appliances that may need repairs, this is where I will get them from. Albeit oven door hinges, they're probably the most expensive light switches I've ever purchased! ;-)
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Both hinges were bent, probably from dropping the door, or leaning on it when it was in the down position.
1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outside, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges.
Other Parts Used:
-
Earle from Taylorsville, UT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
21 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven door sagged & wouldn't close properly
Took off oven door removed all screws to get old hinges out. Replaced with new hinges and put the door back together.
Other Parts Used:
-
Jeff from Palm Beach Gardens, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes would not fully dry in automatic cycle
1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Other Parts Used:
-
Robert from WALDORF, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Richard Mccormick
March 7, 2018
I removed the door for cleaning. How do you reinstall the door? Do i need to remove the front of door to reset springs? Help!!!!
For model number SF385PEEQ
Hi Richard,
Thank you for your question. There is a video on our website that you can reference on how to install the hinge. The oven in the video may not show exactly like the one you have and the part being installed in the video is an inner door glass, but it will give you a general idea on how to install the door. You will find the video under part number PS438400. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Elie
September 20, 2022
Hi,
regarding the oven door hinges (part nbr: WP8053807) , do the package contains 2 hinges or just one. Is there a difference between left and right one? do you currently have it in stock or back order?
Thanks
For model number GERC4110PQ0
Hello Elie, Thank you for your inquiry. We show that this part is a single hinge that can be used for either the left or right hand sides, so there is no difference between the hinges for this model. The stock status for parts is always listed above the Add to Cart button on our site underneath the part information. If you are not sure what a stock status means, you can click on it and a separate window will appear with the explanation for what that status means. In the case of this part, it currently shows as in stock. We hope this helps and if you need help placing an order for a part, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744838
Manufacturer Part Number: WP8053807
Manufacturer Part Number: WP8053807
Brand
Model Number
Description