Product Description
Bellow To Tub Clamp Specifications
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on the washer frame. The main reason you would want to replace the bellow clamp is if it is rusted or damaged, and it is not holding the bellow in place. To remove the bellow clamp, simply use a screwdriver to pop the bellow clamp out of the groove it rests in. Place the new clamp back into the bellow groove until it snaps into place. This is an OEM part from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Whirlpool, Kenmore, Inglis.
Part# WP8540108 replaces these:
AP6013038, 8540108
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Mohsen Y - March 28, 2024
Verified Purchase
It was exactly that I was looking for
It was really good and it worked perfectly
Ray T - June 11, 2019
Verified Purchase
As described promptly shipped.
As described promptly shipped.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
leaking at door
once i figure out how to take off front panel it went quite smoothly also my wife gave me a hand putting the bellows on,her fingers were smaller so it was alittle easier for her
Other Parts Used:
-
william from wauseon, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
22 of 46 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn tub seal causing major water leak.
Removed top of washer. Removed top front panel. Removed old front panel clamp. Removed front door panel. Removed old tub clamp. Then removed torn tub seal. Installed new tub seal. Needed two sets of hands to install new tub seal. Pretty tight installing the new tub seal around drum lip. Might be a good idea to heat up or let your new tub seal soak in water prior to installation. Once tub seal was installed, I installed new tub clamp then re-installed the door switch. After that, I put the front door panel back on. Then tightened down the door switch. Finally, I installed the top front panel and then the top of the washer.
Other Parts Used:
-
Matthew from MENTOR, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking from door
Much easier than I thought. Watched the video a few times.The front control panel gave me a little fight which the video edited that part out And the spring clamp reinstall took the most time.There must be a tool for that??
Other Parts Used:
-
William from BROOKFIELD, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking
Followed the video except to use clamps to hold the Bellow To Front Panel Clamp in place while I worked the clamp around the from of the Bellow. I used a plastic pry tool in place of the suggested screw driver to pry the control panel off.
Other Parts Used:
-
Linda from S SAN FRAN, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
March 9, 2020
How do you put the bellow wire back in place it came out in the wash
Hi David, thank you for your question. We have an installation video for parts like that here: https://youtu.be/WD0W84vc91E. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11746259
Manufacturer Part Number: WP8540108
Manufacturer Part Number: WP8540108
Brand
Model Number
Description