Drive Belt
$110.44
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
PartSelect Number
PS11746376
Manufacturer Part Number
WP8547168
Manufactured by
Whirlpool
Product Description
Drive Belt Specifications
This is the replacement drive belt for your dryer. According to the manufacturer, this belt measures 92.79 inches in length. The drive belt drives the dryer drum. The drive belt should be replaced if it is stretched, worn out, or damaged, and is not driving the drum. The dryer belt is found on the dryer drum. You will need to remove the front panel of your dryer to access of it. Be sure to disconnect power from the dryer before you begin this repair. This belt is sold individually and is an authentic OEM part from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Dryer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer.
This part works with the following products:
Whirlpool, Maytag.
Part# WP8547168 replaces these:
AP6013154, 8547168, WP8547168VP
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
noisy and slow drum speed
1. disconnect power,gas and vent lines
2. pop off top of unit
3. remove front of dryer
4. lay unit on its back
5. remove drum and replace pulley assembly,belt,drum rollers of which it has 2 rear and 2 front
6. reverse above and then remove filter-vent housing and scrape off old seal install new seal
7. re-connect power,gas and vent use again
8. only sad part to whole job was seeing how cheaply whirlpool now makes thier products
2. pop off top of unit
3. remove front of dryer
4. lay unit on its back
5. remove drum and replace pulley assembly,belt,drum rollers of which it has 2 rear and 2 front
6. reverse above and then remove filter-vent housing and scrape off old seal install new seal
7. re-connect power,gas and vent use again
8. only sad part to whole job was seeing how cheaply whirlpool now makes thier products
Other Parts Used:
-
Jeff from Phoenix, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench set
79 of 104 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wore bearing, idler pulley.
Unplug dryer from receptial. Poped top off, useing thin bladed screw driver to push tintion springs, while pulling up on lid. removed two no 10 sheet metal screws, useing 1/4 nut driver, this removes loading door by pulling uo 1/4 inch. Removed twi NO 10 sheet metal screws useing 1/4 nut driver, removed front carrage system. Removed belt then tub. Removed idler arm spring useing plires, used 5/8 inch socket removed sholder bolt with arm. Reverced procedure with one execption. Used two by four to hold tub up so belt could be put on, rolled tub to alline belt. Not bad for 70 Years young. Curtiss
Other Parts Used:
-
Curtiss from Morgan City, LA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
15 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy bad bearing on idle
Taken dry a part remove the belt and then the idle replace with new one taken about 30 minutes.
Other Parts Used:
-
Troy from Homer, GA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
October 17, 2017
Can you tell me what the exact total length of this dryer belt is?
For model number WED6400SW
Hi Steve, Thank you for the question. According to the manufacture this belt is 92.79 Inches. Hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11746376
Manufacturer Part Number: WP8547168
Manufacturer Part Number: WP8547168
Brand
Model Number
Description