Part Videos
Replacing your Whirlpool Washer Front Load Washer Bellow Door Boot Seal - Gray
Troubleshooting
This part fixes the following symptoms:
Leaking | Marks left on clothes | Burning smell
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Maytag, Inglis, Amana.
Part# WPW10381562 replaces these:
AP6020669, W10290499, W10300559, W10381562, WPW10381562VP
Customer Reviews
Filter By Rating:
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Roberto T - 6 days ago
Verified Purchase
The parts just arrived on time! I fixed it myself, front load washer, no more leaks!!! Loved it!
In great conditon and fits perfect!
Allison R - November 23, 2023
Verified Purchase
Bellow for front load washer
The part was in perfect condition and arrived timely. Thanks
Darren F - November 2, 2023
Verified Purchase
The repair was easy and effective except one part :)
The last ring that goes around the whole outside of the seal is a real challenge. The guy on the video does it so easily but if you have had a leak chances are that ring might be rust where the spring is. Might need to try and stretch it out and a good pair of pliers and patients is a must. Also a second pair of hand to stop the ring from coming off while you stretch it could help a lot.
Good luck ...
Quinn P - October 11, 2023
Verified Purchase
Exactly correct part
Shipping was very efficient, the seal was exactly what it was supposed to be. I’ve since ordered other items through partselect.ca and I will in the future also. Quite happy.
Richard S - August 18, 2023
Verified Purchase
Easy repair, part a bit dry
Part arrived fast but looked a bit dry. works well
Darren M - August 4, 2023
Verified Purchase
easy
watched a couple of videos first. went fairly easily. needed an extra hand to start the seal in place but overall easy.
Debora B - July 14, 2023
Verified Purchase
Great product
Watched the video on YouTube had no problems install ….glad to have it repaired thank-you
Henk A - June 26, 2023
Verified Purchase
Well-fitting part, doable diy installation
Part fitted perfectly and after a few weeks of use has not shown any defect or issues. Very happy with it. The original problem was growing leakage from the front area of our washer. We found a small crack in the original tub seal. Installation of the new part was straightforward as we followed the steps in the associated PartSelect video. As stated it was straightforward, but it takes a fair bit of time -- a couple of hours in my case doing this for the first time. I recommend to find a way to raise the washer off the floor to be able to get to the screws that hold the washer front panel. Also, if you have a stacked washer-dryer combo, plan for an extra person to help remove the dryer; there is no way to do the installation while leaving the dryer in place. Bottom line, watch the video carefully before you decide to do this and make sure you are comfortable with all steps. If you are and take your time, it is a good way to save a significant amount of money.
Laura G - May 12, 2023
Verified Purchase
perfect
The part was in great condition, came super, super fast, and my appliance is back in action. Thank you.
Rene A - May 2, 2023
Verified Purchase
Exactly what I needed!
Great quality and specially great video showing how to install the part. Thanks!
- < Prev
- 1
- 2
- 3
- Next >
Customer Repair Stories
Average Repair Rating: 2.9 / 5.0, 5 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer leaking - noticed large crack in the seam of the bellow
9 year old washer started leaking - after inspecting noticed a large hole in the bellow.
The only difficult part was putting the outside band clamp on over the bellow without it slipping out of place - took a few tries. The video was very helpful - I did put hardware into plastic bags based on the steps in the removal for so that I wouldn't forget (or get them mixed up).
I was able to do this project while home from work with a sick kindergartener. Problem started and did the removal the first day ordered the part and it arrived 2 days later - install complete in less than an hour. We went back to school/work with a operating washer by the end of the week! Thank you - it was actually kinda fun and my son bragged to his grandfather that 'he and momma fixed the washer'.
The only difficult part was putting the outside band clamp on over the bellow without it slipping out of place - took a few tries. The video was very helpful - I did put hardware into plastic bags based on the steps in the removal for so that I wouldn't forget (or get them mixed up).
I was able to do this project while home from work with a sick kindergartener. Problem started and did the removal the first day ordered the part and it arrived 2 days later - install complete in less than an hour. We went back to school/work with a operating washer by the end of the week! Thank you - it was actually kinda fun and my son bragged to his grandfather that 'he and momma fixed the washer'.
Other Parts Used:
-
Laura from WAYLAND, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
57 of 63 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hole in the door boot seal and water leaking
I followed the instructions in the video (available on the site) and had no problem whatsoever to replace the boot. This video is so detailed that it is difficult to go wrong.
Only caution I would make is that this may prove to be a bit too much if the person has never ever used tools before.
Only caution I would make is that this may prove to be a bit too much if the person has never ever used tools before.
Other Parts Used:
-
Raghunandan from DORAL, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
First symptom was a small puddle of water below the door which became more after every wash. Further investiation showed a rip in the bellows
My washer is part of a washer/dryer stack and i did not remove the dryer for the repair. I followed a YouTube video that shows the basics of how to do this repair:
1. Remove the spring-compressed outer band. Did this with needle nose pliers. Then removed the bellows from the outside of the frame--really easy.
2. Remove the inner band. Used a stubby philips head screwdriver while pushing the tub inward to get more room.It was awkward, but patience is key. Once that was loose i removed the inner ring then the bellows from the tub.
Total time for removal was maybe 30 min
For the install i took my time and started at the bottom of the tub and pressed the new bellows in the groove making sure it was in properly. Then the ring went on and again, take the time to make sure it's in the groove. Then tighten.
Lastly attache the bellows the the frame of the machine making sure to take your time to properly seat it in the groove.
The most challenging part was getting the outer ring back on. expanding the spring is a challenge. I used just needle-nose pliers to expand it while trying to keep it from slipping off. I believe there is a tool to expand the ring and it's probably worth buying it to make this step easier.
Over all the install took maybe 30-40 min.
Happy i got it fixed. Good luck!
1. Remove the spring-compressed outer band. Did this with needle nose pliers. Then removed the bellows from the outside of the frame--really easy.
2. Remove the inner band. Used a stubby philips head screwdriver while pushing the tub inward to get more room.It was awkward, but patience is key. Once that was loose i removed the inner ring then the bellows from the tub.
Total time for removal was maybe 30 min
For the install i took my time and started at the bottom of the tub and pressed the new bellows in the groove making sure it was in properly. Then the ring went on and again, take the time to make sure it's in the groove. Then tighten.
Lastly attache the bellows the the frame of the machine making sure to take your time to properly seat it in the groove.
The most challenging part was getting the outer ring back on. expanding the spring is a challenge. I used just needle-nose pliers to expand it while trying to keep it from slipping off. I believe there is a tool to expand the ring and it's probably worth buying it to make this step easier.
Over all the install took maybe 30-40 min.
Happy i got it fixed. Good luck!
Other Parts Used:
-
Tom from DOYLESTOWN, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer leaking during spin cycle
Unplug, remove top and bottom panels using nut driver.
The control panel also must be removed; mine just snapped loose, providing access to the top hex-head screws securing the front panel/door assembly. The gasket/bellows is secured to the front panel and tub with circular clamps. The front panel clamp, a wire loop held tight with a spring, must be removed prior to taking off the front panel/door. I used a wide blade flat head screwdriver to pry it off. The door assembly is rather heavy and awkward as the door swings randomly once removed. It may be helpful to secure it to the frame with duct tape prior to removal. Six screws, three top and three bottom, secure the panel. Once removed, there is access to the clamp securing the back of the bellows to the tub. This one is a larger loop with a screw type tensioner. After removing it, the old gasket can be pulled out.
These gaskets have drainage holes at the bottom which must be in line with the drain hole on the tub. Clean the grooved edge where the gasket sits. It fits inside a channel on the bellows. It’s a snug fit and it helps to lubricate the bellow’s channel with liquid soap. Once it is in place, make sure it’s seated properly-there’s a groove that accepts the clamp-and the drainage holes are positioned over the drain at the tub’s bottom. Replace the clamp in its channel and tighten it with a nut driver or screwdriver.
Replace the front panel/door. Next, clean the channel on the front panel and work the front of the bellows into it’s place on the panel. The sprung front clamp can be difficult.
There are spreader tools made for the job, but I just used two needle-nose pliers to stretch the spring. After the new bellows is installed, reassemble the cabinet. I left the bottom panel off until I ran a test cycle to check for leaks.
The control panel also must be removed; mine just snapped loose, providing access to the top hex-head screws securing the front panel/door assembly. The gasket/bellows is secured to the front panel and tub with circular clamps. The front panel clamp, a wire loop held tight with a spring, must be removed prior to taking off the front panel/door. I used a wide blade flat head screwdriver to pry it off. The door assembly is rather heavy and awkward as the door swings randomly once removed. It may be helpful to secure it to the frame with duct tape prior to removal. Six screws, three top and three bottom, secure the panel. Once removed, there is access to the clamp securing the back of the bellows to the tub. This one is a larger loop with a screw type tensioner. After removing it, the old gasket can be pulled out.
These gaskets have drainage holes at the bottom which must be in line with the drain hole on the tub. Clean the grooved edge where the gasket sits. It fits inside a channel on the bellows. It’s a snug fit and it helps to lubricate the bellow’s channel with liquid soap. Once it is in place, make sure it’s seated properly-there’s a groove that accepts the clamp-and the drainage holes are positioned over the drain at the tub’s bottom. Replace the clamp in its channel and tighten it with a nut driver or screwdriver.
Replace the front panel/door. Next, clean the channel on the front panel and work the front of the bellows into it’s place on the panel. The sprung front clamp can be difficult.
There are spreader tools made for the job, but I just used two needle-nose pliers to stretch the spring. After the new bellows is installed, reassemble the cabinet. I left the bottom panel off until I ran a test cycle to check for leaks.
Other Parts Used:
-
John from MIDDLETOWN, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front Boot replacement due to leaky seal
you need to take off the front panel of the washer to do this repair, start at the top cover the bults are in the back, then the bottom panel on the front, then the control panel needs to come off, after all 3 of those are removed you can get to the front panel the door
the door lock also needs to be removed to get this panel off, then a couple small bults at the top of the panel.
once everything is removed you can start take off the old boot.
start with the front boot seal spring clamp using a flat head screwdriver then remove the boot from the inner drum. then the back boot seal clamp will be removed before you can pull the boot off of the washer
installing the new boot I think you should start with inserting the inner seal first then put in a silicone caulking before you pull the outer seal on the inner drum. once that is on re install the clamp and move to the outer seal
this you can use an extra set of hands if someone is around if not it is possible to do it yourself, you will need 3 flat head screw drivers to work the front boot seal spring clamp into place. make sure that is seated well before you start to reinstall the door and other panels
good luck
the door lock also needs to be removed to get this panel off, then a couple small bults at the top of the panel.
once everything is removed you can start take off the old boot.
start with the front boot seal spring clamp using a flat head screwdriver then remove the boot from the inner drum. then the back boot seal clamp will be removed before you can pull the boot off of the washer
installing the new boot I think you should start with inserting the inner seal first then put in a silicone caulking before you pull the outer seal on the inner drum. once that is on re install the clamp and move to the outer seal
this you can use an extra set of hands if someone is around if not it is possible to do it yourself, you will need 3 flat head screw drivers to work the front boot seal spring clamp into place. make sure that is seated well before you start to reinstall the door and other panels
good luck
Other Parts Used:
-
Carl from SHELTON, CT
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Diane
August 9, 2017
How do i change the door seal (bellow)?
For model number coryell
Hello Diane, that is a great question. We actually have a video on our site that will show you how to remove and install the door seal. Hope this helps!
http://www.partselect.com/PS2003890-Whirlpool-12002533-Bellow.htm?SourceCode=6#RepairVideo
37 people found this helpful.
Was this helpful?
Thank you for voting!
Robin Hazlett
January 28, 2018
The lady wrote to ask if the second large piece in the group of pieces at the door opening should be replaced at the same time as the, bellow, is it?. you answered that they are placed next to each other and gave the part numbers, but, my question also is, should i replace them both at the same time?
For model number WFW9050XW00
Hello Robin, thank you for your question. The only reason the tub clamp and bellow clamp should be replaced is if they have broken, or if the spring on the Bellow To Front Panel Clamp has stretched beyond use. If the bellow is the only piece that is damaged, that other pieces should be able to be reused. I hope this helps!
17 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
December 18, 2017
I am looking to purchase the door seal (bellows). Should i also purchase a new clamp ring or is that included?
For model number WFW9150WW00
Hello Michael, Thank you for your inquiry. The clamp rings are sold separately, the bellow to tub clamp is part# WP8540108, and the bellow to front panel clamp is W11032829. Hope this helps!
10 people found this helpful.
Was this helpful?
Thank you for voting!
Farah
October 11, 2019
Hi, is this originally made by whirpool? Or is it by an approved manufacturer? I ordered one through amazon and chunks of rubber ripped with just one month of basic use. It was a lot more poor quality compared to the original which ran for over 5 years. Please reply asap so i can make the order. Thank you
For model number WPW10381562
Hello Farah, thank you for your question. This Bellow is a genuine OEM Whirlpool replacement part obtained from them. Good luck with your repair!
10 people found this helpful.
Was this helpful?
Thank you for voting!
Dennis
December 27, 2017
The door seal is loose, can it be reinstalled or does it need to be replaced? Is it something I can do easy? It appears to be leaking water from the front door seal. Please advise.Thanks
For model number WFW9151yw00
Hi Dennis, Thank you for the question. The door seal is held in place my two clamps. You can try to tighten the clamps or reinstall the seal just in case it was pulled out or came lose. If there is no damaged to the actual seal and it is still lose, you may need to replace the clamps. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Jessica
May 2, 2018
The boot seal on my washer has a tear in it. Now i am finding holes in my clothes when taking them out of the washer. Would replacing this part fix the problem?
For model number MHWE251YG00
Hi Jessica,
Thank you for your question. You might want to take a look to see if there is anything stuck in your washing machine that is causing your clothes and caused your bellow to rip. You will probably want to replace this bellow if it is damaged however. It is the seal between your door and the inside of the drum, so if there is a rip you might eventually get leaking. I hope that helps. Good luck with your repair.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Allan
November 28, 2019
What do we do with triangle tab at the top. Clothes are getting clothes are getting caught on it
For model number WPW10381562
Hi Allan, make sure the seal is properly installed, by watching our video here: https://www.youtube.com/watch?time_continue=1&v=GNrkt7AfW0M&feature=emb_title . Thank you for your question and good luck with your repair!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Isaac
March 10, 2018
I am looking for the part number, I need to order a bellow for my unit?
For model number MHWE201YW00
Hello Isaac,
Thanks for your question. The part number of the bellow for your model is PS11753988.
I hope this helps.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Mark
July 30, 2018
Leaking, does this come with all needed parts to replace, or do i need some kind of kit?
For model number WTW9050W00
Hello Mark, Thank you for the question. There are two clamps that hold the bellow in place. You can reuse the clamps you have no if they are not damaged. If they also need to be replaced, you will need to order part numbers Part Number: PS11773093 and Part Number: PS11746259. Good luck with the repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Tyler
January 29, 2020
I'm getting clothes pinched between the agitator drum and seal. They get caught and then tear as the drum continues spinning. Would ordering a new seal fix this issue? The washer does seem to move around alot more then it use to. Or what you would suggest replacing so that clothes wont be torn in there any more. Ready to order just want to try and be sure to order the right parts. Thanks for any help you can give.
For model number Wfw9150ww02
Hi Tyler, thank you for your question. If you are losing the seal on your bellow, you may have to look at replacing that part and the bellow clamp that keeps it in place. However if your appliance is shaking and moving a lot, you may have to take a look at your shock absorbers for being the issue. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- 2
- 3
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11753988
Manufacturer Part Number: WPW10381562
Manufacturer Part Number: WPW10381562
Brand
Model Number
Description