Product Description
HOSE Specifications
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens you will notice water leaking onto the floor. The tub-to-pump hose is found below the washer tub. To disconnect the hose, you will need to release the clamps that hold it in place with a pair of pliers. When you replace the tub hose, you will need to transfer the ball, air chamber, and clamps from the old pump to the new one. To do this, you will need a set of wire cutters and a new zip tie to replace the one you will need to cut.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking | Will not drain
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Whirlpool, Kenmore, Inglis.
Part# W11366249 replaces these:
AP6888159, 8540012, W10609566, WP8540012
Customer Reviews
Filter By Rating:
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Catherine B - January 22, 2023
Verified Purchase
Part fit perfectly !
Quick delivery / hose fit perfectly - so happy to get the repair done quickly at minimal cost. Thank you Part Select !!
Vernon A - August 15, 2022
Verified Purchase
Fixed leaking from washing machine
The part was well-packed and arrived promptly. It was a simple replacement for my old one, which had developed a split. Very pleased with the result.
Chris T - July 14, 2022
Verified Purchase
Right part for the job. Easy install.
Much better doing these jobs yourself. Save tons of money. All it requires is the part and if you need help a quick google or youtube video will show you how to install it.
Michael M - June 17, 2022
Verified Purchase
Perfect
Perfect
Kyle R - February 17, 2022
Verified Purchase
Perfect
Perfect part. Back in business
Marcel S - January 28, 2022
Verified Purchase
Clothes washer drain
The part was exactly as described, I followed a YouTube to install, and it went well
John T - November 3, 2021
Verified Purchase
Easy repair, part fit great
Part came fast and worked well
ROBERT R - October 21, 2021
Verified Purchase
Perfect fit
The large hose clamp was a bit of a pain but NO MORE LEAK!!
Gerald L - October 1, 2021
Verified Purchase
easy replacement. worked as expected
this part was replaced as i was changing out the pump at the same tme
Len H - November 29, 2020
Verified Purchase
Rubber boot drain
The exact part I needed, 4 day delivery made it real easy for me, will definitely order from you again thank you so much.
- < Prev
- 1
- 2
- 3
- Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 5 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
A wirre from an underwire bra punctured a hole in tub to pump hose. Water leaked out all over the floor.
I searched the internet for parts because we had just had a repairman out to fix the knocking noise in the washer drum. He found an underwire from a bra there and removed it. That cost about $100.
My husband took apart the bottom panel and showed me what the part looked like and I was able to find it on your website. I was able to order the parts and have my husband repair the washer so I was only without a washer for a week and a half. Thank you.
My husband took apart the bottom panel and showed me what the part looked like and I was able to find it on your website. I was able to order the parts and have my husband repair the washer so I was only without a washer for a week and a half. Thank you.
Other Parts Used:
-
Tina from Denver, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Socket set
42 of 81 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no drain, and pin hole in hose causing slight leak
The most time consuming part was fitting the hose back on because of the confined space. Once on the rest was a snap. The drain pump installed just the same as the video, so watch the video! I think in total it took about 30 minutes to complete.
Other Parts Used:
-
Debbie from MOUNT VERNON, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front loading washer is leaking
I followed the steps from online videos to determine where the leak was coming from (cleaned the pump filter, still leaking; checked gasket and inlet hoses).
Finally, I discovered a wet area and cut on the drum-to-pump hose. When I removed the hose, I found that the culprit was a credit card that had broken into shards and slit the side of the hose. I was happy to see it was from the previous owners, which meant it wasn't my fault!
I did have a hard time removing the clamps (double-wire "rotor clip" or "spring clamps", according to Google) holding the hose to the drum and pump. This became a problem when replacing the hose as well. I was not strong enough to squeeze the ends together to loosen the clamp.
Getting the old hose off was easy enough, as was putting the hose back on. The problem was clamping it back on, as I mentioned.
I tried using zip ties, but this was a disaster! I tested it using a rinse and spin cycle, and the zip tie seemed to hold. However, the hose slid off during the first full cycle I ran and dumped at least 15 gallons of water on the floor. Clean up was not fun!
My recommendation (and what I finally went with) is to use hose clamps with the small screw that lets you tighten the clamp with a screw driver. I used that on both the connection to the drum and the connection to the pump and I've had no issues since.
Overall, it's a quick fix once you have the hose replacement and the right parts. If I'd gotten the hose clamps right away, I could have been done in 30 minutes.
Hope this helps and good luck with your repairs!
Finally, I discovered a wet area and cut on the drum-to-pump hose. When I removed the hose, I found that the culprit was a credit card that had broken into shards and slit the side of the hose. I was happy to see it was from the previous owners, which meant it wasn't my fault!
I did have a hard time removing the clamps (double-wire "rotor clip" or "spring clamps", according to Google) holding the hose to the drum and pump. This became a problem when replacing the hose as well. I was not strong enough to squeeze the ends together to loosen the clamp.
Getting the old hose off was easy enough, as was putting the hose back on. The problem was clamping it back on, as I mentioned.
I tried using zip ties, but this was a disaster! I tested it using a rinse and spin cycle, and the zip tie seemed to hold. However, the hose slid off during the first full cycle I ran and dumped at least 15 gallons of water on the floor. Clean up was not fun!
My recommendation (and what I finally went with) is to use hose clamps with the small screw that lets you tighten the clamp with a screw driver. I used that on both the connection to the drum and the connection to the pump and I've had no issues since.
Overall, it's a quick fix once you have the hose replacement and the right parts. If I'd gotten the hose clamps right away, I could have been done in 30 minutes.
Hope this helps and good luck with your repairs!
Other Parts Used:
-
Michelle from WAREHAM, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
mice chewed thru hose
Pretty straight forward , It is a tight work are especially laying on your stomach. To make installation easier I recommend buying a 3-4 inch hose clamp instead of trying to use the old pinch style clamp. You will only need a zip tie if you reuse the existing clamps. remember to remove the plastic ball from the old rubber hose into the new hose.
Other Parts Used:
-
oscar from MEMPHIS, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain/Pump bellow (washer tub to pump hose) punctured. Leaked excessive amount of water.
Removed top lid (only to be able to remove pressure sensor hose easily). Removed hose clamps and tied the ends together in order to keep in loose position. Then squeezed the damaged hose up between sidewall and tub to remove pressure sensor rubber pipe. Installed Hose with clamps tied in the loose position with thin wire. Attached the pressure sensor pipe. Loosened the thin wire holding clamps loose. Tested for leaks by running washer. Leak repaired.
Other Parts Used:
-
Vern from LAREDO, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rick
November 24, 2021
Does the ball go inside boot or on top. I have a f21 fault and pump is fine. No clog anywhere so I think the ball clogs the drain inlet to pump.
For model number 11047561604
Hi Rick,
Thank you for your question. This ball goes into the drain hose between the outer tub and the drain pump and goes into the wider end of the hose. You will need to inspect the hose to verify if the ball is causing the issue. We hope this helps! If you have any questions, please let us know.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Marsha
April 12, 2023
Is it normal for water to collect in the tub-to-pump hose ? We notice a strong bad smell coming from it.
For model number mhwe201yw00
Hello Marsha, thank you for the question. The tub-to-pump hose, part number PS12723931, seems clogged and you may need to clean it. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS12723931
Manufacturer Part Number: W11366249
Manufacturer Part Number: W11366249
Brand
Model Number
Description