Troubleshooting
This part fixes the following symptoms:
No hot or cold water | Leaking
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# 12002158 replaces these:
AP4010168, 1063699, 12002158, 22003372, 22004209
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Gary M - January 24, 2019
Verified Purchase
Easy repair
Once the right part arrived it took not more than half an hour to install and test. Incredibly fast delivery. Invoice said three days. It actually arrived the next day.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No cold Water
Shut-off water + power.With the putty knive; slide it under the front of the top to push back on the spring clips.The top will lift easily and it is hinged.The Water inlet unit in the back has a plastic cover.Remove carefully.One screw holds the unit in place. Remove and the the unit will slide out to the left. It's now easy to disconnect the hoses from the unit. The wiring to the coils is color coded,take note for proper reconnecting. Remove stakon connectors from the valve coils. Careful, do not pull on the wire but wiggle it of the coil connection.Pay attention to the routing of the wire harness. Also the kit comes with a clear plastic splash shield. make sure the new goes in the right place.Now the old water inlet valve can be removed from the metal bracket.One srew.Assembly goes in reverse
Other Parts Used:
-
Reinhard from TORRANCE, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
December 1, 2017
Can you adjust the flow of the water from the water inlet valve? It seems the cold water side is filling much slower that it should
For model number MAV7600AWW
Hello Michael,
The water inlet valve may not be receiving sufficient power for the cold water side. We would advise checking it with a multi-meter if the inlet hose is not clogged and replacing it if it is not showing continuity.
I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Scott
October 31, 2019
I need a water inlet valve for my washer. Water fills the tub when hose pressure left on. Serial number is 23567899ee. Please provide part number.
For model number MAV7501EWW
Hello Scott, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS11739520. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Stanley
December 7, 2019
Washer filled with water but will not start.Tried raising water level and will not add more water. Looks like it doesn't get any power. Checked outlet and it is good. Sounds like maybe a fuse or something similar. Any suggestions?
For model number MAV7700AWW
Hi Stanley, this is likely to be a faulty lid switch, belt or motor. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Stephen
May 3, 2019
I have a Maytag atlantis washer that was working fine. Ran a load yesterday worked fine, noticed when off started to fill for about 5seconds and then stop, and then shortly later do the same thing. When unplugged stops doing this. Could this be the pressure switch? Thanks
For model number mav8600aww
Hello Stephen, thank you for your question. Yes it doesn't sound like the pressure switch, could be an issue related to the timer. We would also recommend testing the valve to be sure that isn't the issue. Here is a link to test the valve. https://www.partselect.com/Washer+test-water-valve+repair.htm. I hope this helps!
Was this helpful?
Thank you for voting!
Epifanio
December 20, 2023
Water never stops filling up starts ,water still running ,I shut off hot water supply and and left cold on. And works fine what do I need as far as parts if. I leave both on. The water keeps filling tank and washer on cycle ??????
For model number Mav6257aww
Hi Epifanio, thank you for your question! Based on the description, the issue is with the water inlet valve, part number PS2003611. The water inlet valve with thermistor controls the water flow to the washer while monitoring the water temperature. We would recommend replacing the inlet valve to fix the issue. Good luck with your repair!
Was this helpful?
Thank you for voting!
Erich
January 9, 2019
What is your return policy if the part does not fix my problem?
Hello Erich, Thank you for the question. Here is a link to our return policy. Hope this helps!
https://www.partselect.com/Thirty-Day-Returns.htm
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2003611
Manufacturer Part Number: 12002158
Manufacturer Part Number: 12002158
Brand
Model Number
Description