Thermostat Cut-Out
Fits your RVM1435WK01!
$47.59
Special Order
Fits your RVM1435WK01!
PartSelect Number
PS239319
Manufacturer Part Number
WB27X10195
Manufactured by
GE
Product Description
Thermostat Cut-Out Specifications
Also known as Thermostat or Humidity Sensor for Fault Code.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Won’t turn on
This part works with the following products:
Microwave, Range.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WB27X10195 replaces these:
AP2026103, 769937, WB20X0141, WB20X0171, WB20X141, WB20X171, WB27X10665, WB27X10670
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven would not power up
There are 4 thermostats (aka TCO = Thermal Cut Out) in the GE JVM1440BH04
The schematic is under the cover in a black envelope to the top left of the unit if you face the door.
Check the fuse first. You can remove the front grate, then the numpad on the right. The fuse is right behind it. It's a 250V 20A Class F fuse.
There are four (4) TCOs or Thermal Cut Out thermostats in this puppy:
1) There is a thermostat behind the button panel to the left, facing down. If blown, it breaks the power coming into the unit and will cause a no power situation.
2) There is another TCO or thermostat near the top lamp, to the left, in a small cavity. That one also breaks power to the unit and will cause a no power situation. It's a 100 C / 0 C thermostat. This was the one that blew on me after I left the stove running (for heating in a black-out) under the microwave.
"Cavity TCO" or "Thermostat" part number 61 on the schematics, part number PS239319
3) There is yet another power-breaking TCO or thermostat in the cavity behind the fan that cools the microwave coils. You have to remove the sheet metal on the right of the microwave to access it. This one also breaks power and will cause a no power situation.
1), 2) and 3) should test out to be 0 Ohms with a resistance meter (Digital Multimeter) if working correctly.
4) There is a thermostat which normally does not let current through it. It is mounted in a vertical position to the back wall behind the front panel on the right. This one is used for the sensor reheat function apparently and will close when the temperature in the microwave reaches approx. 60 C.
4) should have infinite resistance with a resistance meter under normal circumstances.
The schematic is under the cover in a black envelope to the top left of the unit if you face the door.
Check the fuse first. You can remove the front grate, then the numpad on the right. The fuse is right behind it. It's a 250V 20A Class F fuse.
There are four (4) TCOs or Thermal Cut Out thermostats in this puppy:
1) There is a thermostat behind the button panel to the left, facing down. If blown, it breaks the power coming into the unit and will cause a no power situation.
2) There is another TCO or thermostat near the top lamp, to the left, in a small cavity. That one also breaks power to the unit and will cause a no power situation. It's a 100 C / 0 C thermostat. This was the one that blew on me after I left the stove running (for heating in a black-out) under the microwave.
"Cavity TCO" or "Thermostat" part number 61 on the schematics, part number PS239319
3) There is yet another power-breaking TCO or thermostat in the cavity behind the fan that cools the microwave coils. You have to remove the sheet metal on the right of the microwave to access it. This one also breaks power and will cause a no power situation.
1), 2) and 3) should test out to be 0 Ohms with a resistance meter (Digital Multimeter) if working correctly.
4) There is a thermostat which normally does not let current through it. It is mounted in a vertical position to the back wall behind the front panel on the right. This one is used for the sensor reheat function apparently and will close when the temperature in the microwave reaches approx. 60 C.
4) should have infinite resistance with a resistance meter under normal circumstances.
Other Parts Used:
-
Andras from Lexington, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
44 of 59 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to microwave
Had trouble isolating the problem, so I had a repairman identify the problem, then I ordered the part and replaced it myself.
Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.
Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.
Other Parts Used:
-
James from Highland, UT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
14 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave dead
First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.
Other Parts Used:
-
Jerry from Lillian, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
10 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tony
February 16, 2018
If the wire on one side of this part is melted does it mean that part is bad? Or does it mean something else is wrong? The microwave works fine i just smelled burning wires and found this one melted wire.
Hello Tony, Thank you for your inquiry. You can test the part with a multimeter to see if it has continuity. The reading should be close to 0 ohms. If the wire has melted, for safety reasons, you should probably replace the wiring harness as well. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Wes
August 6, 2018
My microwave turns on on his own and show me massage ;shorted steam sensor; is this thermostat cut-out part #ps239319 will solve the problem? Thanks wes
For model number jvm1540sn1ss
Hello Wes, thank you for your question. Usually if the unit is starting on its own there is an issue with one or more of the three door switches. I would recommend testing them with an multimeter to verify which one(s) are faulty. You can also test the TCO thermostat, part number WB27X10195. You can test the part with a multimeter to see if it has continuity. The reading should be close to 0 ohms. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joe
December 11, 2018
Is there a video of how to remove covers to get to components?
For model number jvm1750sp1ss
Hi Joe, thank you for your question. We do not have a video for your model specifically however we do have a video that shows how to generally do this. You can view it here: https://www.youtube.com/watch?v=-yUtoBg17Jg&t=6s. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS239319
Manufacturer Part Number: WB27X10195
Manufacturer Part Number: WB27X10195
Brand
Model Number
Description