Part Location Diagram of 241675704 Frigidaire Refrigerator Ice Dispenser Solenoid
See part F45 in the diagram
Replacing your Frigidaire Refrigerator Refrigerator Ice Dispenser Solenoid
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Refrigerator Ice Dispenser Solenoid

 Fits your FRS6R5ESB4!
$122.70
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your FRS6R5ESB4!
PartSelect Number PS8691994
Manufacturer Part Number 241675704
Manufactured by Frigidaire
Product Description

Refrigerator Ice Dispenser Solenoid Specifications

The cube solenoid allows cube or crushed ice to be dispensed on demand. 120V 60Hz
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Refrigerator Refrigerator Ice Dispenser Solenoid

Replacing your Frigidaire Refrigerator Refrigerator Ice Dispenser Solenoid
Troubleshooting
This part fixes the following symptoms:
Ice maker won’t dispense ice | Ice maker not making ice
This part works with the following products:
Refrigerator.
This part works with the following products:
Frigidaire, Kenmore, Electrolux, Crosley.
Part# 241675704 replaces these:
AP5780907, 241675701, 241675801, 5304404333, 5304406819, 7241675701, 7241675801
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 3 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The ice dispenser would only dispense crushed ice, Fridge door cluncked when opening and closing
For the ice dispenser, I read a blog that pointed me right to the solenoid that controls the linkage for the crushed /cubed ice.I first unplugged the fridge. Then removed the ice maker basket. Removed 2 ea screws from each side of the supports of the lower brackets. Then lifted the tray assy off the mounting bracket, moving the front of the bracket down you can then unhook the power/control connector.
The tray then comes right out. Once out you remove two screws that hold a plastic plate on. With this removed you can see the solenoid that actuates the linkage for the ice cube and crushed ice. You then remove 2 ea machine screws that hold the solenoid in. Remove grd. wire. and pull power wires off tabs. You can then remove the solenoid by sliding it out of the plastic retainer. With it out you install the new plunger and reassemble in the reverse order. 15 mins tops.

The main Refidgerator door, made a cluncking sound. Lube didn't help. I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 10 mins
Other Parts Used:
Door Closing Cam Hinge Bearing
  • Al from Shakopee, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
111 of 128 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker wouldn't change from crushed to cubed ice
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
Other Parts Used:
  • robert from sioux falls, SD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
56 of 85 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Other Parts Used:
  • Mary from MAGNOLIA, AR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

35 questions answered by our experts.
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ron
January 3, 2018
Makes ice cube but wont switch to crushed what is the problem
For model number FFHB2740PP5A
PartSelect logo
Hi Ron, Thank you for your question. Crushed cubes is actually the default on your appliance when dispensing ice, so it is likely that your solenoid assembly is the issue. I would advise testing the part with a multi meter to double check. I hope that helps. Good luck with your repair.

8 people found this helpful.

Was this helpful?
Thank you for voting!
Betty
January 8, 2019
How difficult is it to change the crused/cube ice solenoid assembly?
For model number LFHB2741PF5A
PartSelect logo
Hello Betty, Thank you for the question. Previous customers have said it was a easy repair. Here is a repair story from a previous customer. First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire.Thank you for your inquiry, good luck with this repair!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Brad
February 11, 2020
My fridge only dispenses crushed ice, will this solve the problem so i can dispense ice cubes?
For model number FGSS2635TF0
PartSelect logo
Hello Brad, Thank you for the question. Yes, the Ice Dispenser Solenoid is the most common issue when the dispenser only dispenses Crushed or Cubed ice and not both. We hope this helps.

4 people found this helpful.

Was this helpful?
Thank you for voting!
Chad
April 27, 2018
Will not dispense cubes but only crushed... assume solenoid.. ??
For model number FPHB2899LF4
PartSelect logo
Hello Chad, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: crushed/cubed ice solenoid assembly, solenoid actuator, and solenoid spring. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Jorge
December 24, 2017
I replaced the auger motor on my Frigidaire refrigerator fghb2844lfe but the auger motor still not turning. How can i test the solenoid to see if that is the problem?
For model number FGHB2844LFE
PartSelect logo
Hi Jorge, Thank you for the question. The solenoid controls the crushes or cubed ice option. You can try to switch it from cubed to crushed to see if it dispenses and the solenoid is in the down position. Also make sure the ice lever is making contact with the switch on the ice maker. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Augustus
November 4, 2019
Kenmore refrigerator will not dispense ice, it makes ice, but will not dispense cube or crush ice
For model number 253.70313211
PartSelect logo
Hi Augustus, thank you for your question. The first two parts that you should check would be your dispenser solenoid and this crushed/cubed ice solenoid. They can be tested with a multi meter. We have a video that shows how to use a multi meter here: https://www.youtube.com/watch?v=bWC44fHn0As. Good luck with your repair.

3 people found this helpful.

Was this helpful?
Thank you for voting!
Beverly
June 10, 2019
My ice maker is stuck on the crushed ice cycle and will not switch back to the cube cycle other than that everything works fine.
For model number PLHS267ZCB2
PartSelect logo
Hi Beverly, Thank you for the question. The solenoid controls the crushes or cubed ice option. You can try to switch it from cubed to crushed to see if it dispenses and the solenoid is in the down position. The Solenoid may be defective and need to be replaced. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Pat
February 18, 2020
Hi, I'm going to order and attempt changing the water inlet valve. I did read in some earlier posts about also changing the diode kit. Is there a part number for that. Thanks, pat.
For model number EW28BS71IS1
PartSelect logo
Hello Pat, Thank you for the question. Checking this model it does not have or require a Diode. We hope this helps.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Dan
January 30, 2023
My unit will not make large cubes how dos the ice dispenser work
For model number Ew23bc85ks4
PartSelect logo
Hello Dan, We are glad you asked! Poor water flow affects your ice maker produces ice cubes. Too little water can cause the cubes to come out too small or hollow. Freezer temperatures below -10°F can cause ice cubes to freeze too quickly on the outside, which may trigger the thermostat in the ice maker to eject the cubes before they’ve become completely solid in the middle. The Water Inlet Valve PS7321353 or Temperature Sensor PS1765215 may be the issue. We hope this is of some help to you.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Linda
December 27, 2019
My Frigidaire makes ice but won't dispense the ice or water what part need replacing
For model number FFHS2622MSWA
PartSelect logo
Hello Linda, thank you for your inquiry. If your ice maker is not dispensing ice, we recommend replacing the Ice Container and Auger Assembly. This can be located under part number PS1991430. We hope this information helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS8691994
Manufacturer Part Number: 241675704
Brand
Model Number
Description
Frigidaire
20462151B
Refrigerator - Refrigerator
Kenmore
25344302400
Refrigerator
Kenmore
25344302401
Refrigerator
Kenmore
25344303400
Refrigerator
Kenmore
25344303401
Refrigerator
Kenmore
25344303402
Refrigerator
Kenmore
25344303403
Refrigerator
Kenmore
25344304400
Refrigerator
Kenmore
25344304401
Refrigerator
Kenmore
25344309400
Refrigerator
Kenmore
25344309401
Refrigerator
Kenmore
25344333600
Refrigerator
Kenmore
25344333601
Refrigerator
Kenmore
25344333602
Refrigerator
Kenmore
25344333603
Refrigerator
Kenmore
25344333604
Refrigerator
Kenmore
25344333605
Refrigerator
Kenmore
25344333606
Refrigerator
Kenmore
25344333607
Refrigerator
Kenmore
25344333608
Refrigerator
Kenmore
25344333609
Refrigerator
Kenmore
2534433360A
Refrigerator
Kenmore
25344352400
Refrigerator
Kenmore
25344352401
Refrigerator
Kenmore
25344352403
Refrigerator
Kenmore
25344352404
Refrigerator
Kenmore
25344352405
Refrigerator
Kenmore
25344352406
Refrigerator
Kenmore
25344352407
Refrigerator
Kenmore
25344352408
Refrigerator
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service