Part Location Diagram of 807145201 Frigidaire Lower Spray Arm Support
See part 10 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Lower Spray Arm Support

★★★★★
★★★★★
13 Reviews
$39.33
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS9865072
Manufacturer Part Number 807145201
Manufactured by Frigidaire
Product Description

Lower Spray Arm Support Specifications

This plastic cover and stem assembly helps hold the lower spray arm in place.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Not cleaning dishes properly | Noisy | Not draining
This part works with the following products:
Dishwasher.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Gibson.
Part# 807145201 replaces these:
AP5948918, 154245501
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
13 Reviews
4.7
Filter By Rating:
  • 5 Stars
    11
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Star
    0
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
Customer Repair Stories
 Average Repair Rating: 4.5 / 5.0, 16 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Dishwasher was growing mold on inside lid door. Also the glasses were not looking clean. Appeared as if they were not getting rinsed well enough.
First I removed the two screws that hold the lower front cover of the dishwasher to get under the dishwasher. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then opened the dishwasher door and removed the old element and replaced it with the new element. I closed the dishwasher door and reconnected the two wires making sure that I put the proper wire on the proper post. I then put the two screws back on the element to hold it in place Next I replaed the cover on the front and tested the dishwasher for heat by running it empty.
Other Parts Used:
Heating Element
  • Matt from Bowling Green, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
24 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lock Down On Stem Stripped
Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks
Other Parts Used:
  • Ronnie from Elberfeld, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack not being cleaned
This was pretty easy. It was a guess as to the problem, but there much debate , if the water isn't moving it had to be the pump, right?. So i replaced the circulation pump. 2 screws on the top and two trim screws on the bottom, and it slides right out. Then UNPLUG IT.. Take the screen out of the bottom on the inside and make sure you get all the water out or it will end up on the floor when you tip it on it's side. The directions were ok, i looked over them briefly but didn't use them. tools were, phillips srewdriver, torx driver (pump bracket srews) wire stripper/crimper (for the plug adaptor) and a heat gun, (for the heat shrink tube for the crimp connection). Overall it was pretty easy. the pump was made to be easy to replace. 45 min and back in action.
Other Parts Used:
Dishwasher Circulation Motor & Pump Kit with Harness
  • steven from Walnut Creek, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke nubs off of stem when cleaning
I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).
Other Parts Used:
  • Glen from Chicago, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The small "nubs" on the assembly had worn off.
After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks
Other Parts Used:
  • Peggy from Minerva, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom spinner wouldn't stay on
VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!
Other Parts Used:
  • Kathey from Humboldt, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
PARTS ORDER TOOK TOO LONG TO ARRIVE
The repair was not the problem. The problem was getting the parts I ordered. When the parts finally shipped I had to wait for them because they just sat in a FedEx shipping warehouse for about a week delaying the repair.
Other Parts Used:
Lower Spray Arm Support Lower Spray Arm
  • LUKE from MARIETTA, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stem assembly was broken.
I removed the three screws that held the stem assembly in place, removed the old stem assembly and replaced it with the new one. Replaced the screws and began using the dishwasher again.
Other Parts Used:
  • Larry from Fort Huachuca, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken part that holds bottom spray arm on.
This was great! Removed 3 screws, took out old broken part, set in new part and screwed tight! 1 2 3 and done. Very Fast shipping less than 24 hrs.. WIFE IS HAPPY. Ted W.
Other Parts Used:
  • Theo. J. from Green Bay, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Other Parts Used:
  • david from hull, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robbin
January 23, 2023
Water will not drain. What parts will I need
For model number LFID2426TF1A
PartSelect logo
Hello Robbin, Thank you for your inquiry. Researching the model number you have provided, we would recommend checking the following parts: the drain pump, the drain hose and the drain filter. Check the hose and filter for any debris or restrictions and clean if needed, and you can test the pump with a multimeter. Good luck with your repair.

Was this helpful?
Thank you for voting!
Related Parts:
Jessica
February 24, 2023
I wanted to make certain that this part will fit my dishwasher as the part numbers do not match.
For model number FDB520RHS0
PartSelect logo
Hello Jessica, thank you for your question. Yes, this Support PS9865072 is the correct one for your model. Good luck with your repair.

Was this helpful?
Thank you for voting!
Mat
March 9, 2023
My dishwasher is FDP750RCS0 . The part Lower Spray Arm Support Part #: PS9865072 suggested for my dishwasher looks different, The side with 2 screws seems to go further and appears differently shaped. Is this the correct part?
For model number FDP750RCS0
PartSelect logo
Hi Mat, thank you for reaching out. According to our research on your model, the lower spray arm support, part number PS9865072, is compatible with your model. We hope this information helps!

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS9865072
Manufacturer Part Number: 807145201
Brand
Model Number
Description
Frigidaire
004621710A
Dishwasher - Dishwasher
Frigidaire
004621711A
Dishwasher - Dishwasher
Kenmore
58714102800
Dishwasher
Kenmore
58714112400
Dishwasher
Kenmore
58714112401
Dishwasher
Kenmore
58714112402
Dishwasher
Kenmore
58714113400
Dishwasher
Kenmore
58714113401
Dishwasher
Kenmore
58714113402
Dishwasher
Kenmore
58714114400
Dishwasher
Kenmore
58714114401
Dishwasher
Kenmore
58714114402
Dishwasher
Kenmore
58714119400
Dishwasher
Kenmore
58714119401
Dishwasher
Kenmore
58714119402
Dishwasher
Kenmore
58714131100
Dishwasher
Kenmore
58714131101
Dishwasher
Kenmore
58714131102
Dishwasher
Kenmore
58714132100
Dishwasher
Kenmore
58714132101
Dishwasher
Kenmore
58714132102
Dishwasher
Kenmore
58714134100
Dishwasher
Kenmore
58714134101
Dishwasher
Kenmore
58714134102
Dishwasher
Kenmore
58714139100
Dishwasher
Kenmore
58714139101
Dishwasher
Kenmore
58714139102
Dishwasher
Kenmore
58714153400
Dishwasher
Kenmore
58714153401
Dishwasher
Kenmore
58714153402
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service