Part Location Diagram of WD03X10026 GE Spring Plunger
See part 837 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Spring Plunger

$21.88
  Special Order
PartSelect Number PS1019010
Manufacturer Part Number WD03X10026
Manufactured by GE
Product Description

Spring Plunger Specifications

This is a replacement spring plunger for your dishwasher. The spring is approximately 1 inch in length and is sold individually. The spring plunger helps your door latch correctly, and if the spring is missing or damaged, you can experience a door latch failure, and your dishwasher may not start. This is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Door latch failure
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric, Hotpoint.
Part# WD03X10026 replaces these:
AP3872943, 1168253, WD03X10025
Back to Top
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 4 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
would not start
First I removed the 6 screws that hold the inside cover on the door.Then I remover the plastic cover over the switches,pulled out the switches and disconnected the 2 wires from each switch and connected connected them to the new switches exactly as they were on the old switches.Then reinstalled the switches in their holders.I then removed the plunger and spring from between the switches and installed the new spring and plunger exactly like the old one was installed.I reinstalled the door cover making sure everything was in it's place,I put the screws in the door cover and I was done.It was a very simple job. Mike
Other Parts Used:
Interlock Plunger Switch Interlock
  • MICHAEL from ORLEANS, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
46 of 56 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cover, Interlock Heats Ups And Bends Causing Switch Problems
Ordered your new and improved interlock cover made with better plastic (thank you). Your new spring is also better. It's bigger and longer and is now the right size. (Thank you). Your parts are better than oem. The interlock is easy to get to. The oem one is black and you can see that it is bulged. The replacement one is gray speckled with white and black. You can see the improvement by just making a comparison. Just unclip the old one and clip in the new one. . Repace panel cover. Now it works and should work now for many a year. Thanks! Parts select.
Other Parts Used:
Interlock Plunger Interlock Cover
  • JAMES from MAYFIELD, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
15 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher wouldn't start/reset
Very simple. Took off back cover with screwdriver. Popped off back cap found in center top inside. Replaced spring and white stick looking thing. Put black cover and then back panel back on. Instantly worked again.
Other Parts Used:
Interlock Cover Interlock Plunger
  • Jessica from Chicago, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It makes a beeping sound in the middle of the dishwashing.
Remove the screws from the door and replace the switch interlock and door latch.

The problem is fixed and the dishwasher works fine so far (about three weeks) now.

The source of the problem looks more like the door latch because I use to push the door in to get it going before I replace the parts.

The video I received via email that show the how to do it was very helpful.

————-
Update after more than month. (12/30/2020)
The problem still persists. However I have a possible solution for it that doesn’t require any parts at all. The entire dishwasher is tilted backward. As the washing started and the water pileup in the bottoms of the dishwasher, it pull the entire dishwasher back work causing the switch interlock to release (open the relay causing the door open been sounds).

Level the dishwasher so that it doesn’t tilt backwards and this should fix the issue. I will post the latest after a month. If you need more info I can send a picture to describe the issue more clearly.
—————————
Update 01-06-2021
The problem still persists. The above theory I had was wrong and didn’t make any difference.

However, I have a permanent solution but it may not be ideal for most people ??. The relay that get close/open when the door is close/open is now always CLOSED. To start the dishwasher just press start and make sure you don’t open the door while the dishwasher is running. It will not stop. I am sorry and I know it’s not a good solution but it’s kind of funny.
Other Parts Used:
Door Latch Door Handle Actuator Interlock Plunger Switch Interlock Retainer Handle - Black Recess Door Spring Latch Handle
  • ANTENEH B from EAST GRANBY, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jennifer
August 14, 2019
Door closes and latches but will not beep/turn on. If i keep opening/closing it i can eventually get it to beep/turn on and it runs just fine. It is getting worse. Please let me know what i need to replace to end the struggle?
For model number EDW500015CC
PartSelect logo
Hello Jennifer, thank you for inquiring. This sounds like either a faulty Interlock Switch part number PS1021382 or Interlock Plunger part number PS1993857 for your model. I hope this helps and good luck with your repair!

4 people found this helpful.

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1019010
Manufacturer Part Number: WD03X10026
Brand
Model Number
Description
General Electric
4070100
Dishwasher
General Electric
4070110
Dishwasher
General Electric
4070500
Dishwasher
General Electric
4070510
General Electric
4070600
Dishwasher
General Electric
4070610
Dishwasher
General Electric
4070800
Dishwasher
General Electric
4070810
General Electric
4071100
Dishwasher
General Electric
4071110
General Electric
4071120
Dishwasher
General Electric
4071500
Dishwasher
General Electric
4071510
General Electric
4071520
Dishwasher
General Electric
4071600
Dishwasher
General Electric
4071610
General Electric
4071620
Dishwasher
General Electric
EDW4000G10BB
Dishwasher
General Electric
EDW4000G10CC
Dishwasher
General Electric
EDW4000G10WW
Dishwasher
General Electric
EDW4060G10SS
Dishwasher
General Electric
EDW5000L00BB
Dishwasher
General Electric
EDW5000L00CC
Dishwasher
General Electric
EDW5000L00WW
Dishwasher
General Electric
EDW5000L15BB
Dishwasher
General Electric
EDW5000L15CC
Dishwasher
General Electric
EDW5000L15WW
Dishwasher
General Electric
EDW5060L00SS
Dishwasher
General Electric
EDW5060L15SS
Dishwasher
General Electric
EDW5100N00BB
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service