Product Description
Injector Sleeve Specifications
This is a top mounting style injector sleeve.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# WP215447 replaces these:
AP6005849, 2-15447, 215447
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Rodney D - February 19, 2020
Verified Purchase
My Washer Should Last Another Decade!
With the injector sleeve assembly I recently ordered I was able to repair my thirty year old Maytag in minutes - now you know how I'll be spending my spare time. Thanks PartSelect!
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 18 reviews.
What's this?
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Front load washing machine leaking on floor while in fill mode.
Removed two screws at bottom of front panel and then removed front panel. Then removed two self-tapping bolts (one on each side) holding top panel in place and swung the panel up, out of the way, to expose top of tub and water injection components. Cut off one pinch clamp and loosened screw clamp holding two injector hoses to the injector sleeve. Removed these water injector hoses from injector sleeve assembly which is mounted on top of left side panel upper flange. Replaced deteriorated rubber injector valve, nozzle and the sleeve for the injector (plastic housing containing the injector valve and nozzle). Also replaced deteriorated injector tube seal where injector tube elbow mounts to top of tub assembly. Reinstalled injector hoses with a replacement screw clamp to replace the one cut off. tightened the new clamp and the other, original, screw clamp and checked for leaks. This solved the leakage problem. Secured top panel and re-installed front panel. Hardest part of the task was determining where the leak emanated from but once found and parts ordered, it was a relative snap to fix.
Other Parts Used:
-
Catherine from Wyandotte, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
175 of 185 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer leaked from top, left corner of machine.
Removed front of machine; then tilted back the top of machine, after removing the two screws in top front. Removed the old parts, trimmed the injector hose which was slightly longer than necessary, put new injector nozzle in ruber injector valve and inserted into the new sleeve, clamping the new hose to sleeve as well as clamping the remaining functioning hose to sleeve. The new sleeve mounting bracket was slightly different from the old one, but I was able to make it work with a small block of wood and two screws. The washing macine no longer leaks, the parts arrived timely, and the price was right. Thanks.
Other Parts Used:
-
Robert from Hudson, WI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
21 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was leaking on the floor
I took the front panel off the machine and then removed the two screws that held the top on. Cut the hose clamps off the hoses and replace the injector sleeve, valve, housing, and hose to tub. I am not sure what the function of this is, other than to inject air into the water before it goes into the tub. Very easy to do if you know how to open up the washing machine.
Other Parts Used:
-
Mark from Park City, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
17 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water
The washer leaked only when i used warm or hot water. I found that the rubber injector valve would get to soft when using hot water,allowing the water to leak through and bubble out and onto the floor. I went ahead and replaced the injector nozzle, injector sleeve and the rubber injector valve. I ordered the parts monday morning and they arrived the next day. Excellent service.
Other Parts Used:
-
Dennis from scottdale, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had a leak that started just under the rim of the washer and then ran down the outside of the machine
Your website is wonderful. I read another womans account of how she fixed her machine and then I just followed her instructions...how cool is that!
Other Parts Used:
-
Janis from Georgetown, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water rear left side
This happened once before and had I remembered how to get the front door off and lift the top it would have taken me less time. I actually spent more time assessing prior to ordering parts than in repairing once the parts came.
One odd thing - it only leaked when the hot water was entering (if the settings were on cold only no leak - no idea why that should be).
Anyway, this injector and the rubber housing it slides into get old and clogged or deteriorate. I ordered all the parts and replace them - but probably only needed to replace the plastic injector nozzel and the rubber sleeve it fits into.
All good now - no more leaks (until the next time!)
One odd thing - it only leaked when the hot water was entering (if the settings were on cold only no leak - no idea why that should be).
Anyway, this injector and the rubber housing it slides into get old and clogged or deteriorate. I ordered all the parts and replace them - but probably only needed to replace the plastic injector nozzel and the rubber sleeve it fits into.
All good now - no more leaks (until the next time!)
Other Parts Used:
-
Forrest from San Diego, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
8 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer leaking
First I took all the screws out of the side and back cabinet, then tried to pry off the top, after breaking a couple of clips, saw that the front came off with two screws at the bottom, then removed, then two hex head screws to hold on the top, then lift top and saw that the injector was clogged and leaking out the top. If I had read the repair section first, I could have saved alot of time by not removing all the side and back screws. This would be a simple 15 minute job, if you follow the repair guide. Just cut off the clamps, stick in the injector and holder , reclamp and reassemble the washer.
Other Parts Used:
-
danny from Seymour, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hot water overflow injector, ran onto floor
You will need 2 hose clamps not sold as maytag parts.
Remove front washer panel screws.
Remove bolts holding front of top to side panels
Remove hose clamp from front hose to injector sleeve.
Twist fill hose ccw 90 degrees at tub fitting to remove.
Clean corrosion at tub attachment point wuth wire brush.
Paint bare metal to seal. Allow to thoroughly dry.
Remove injector sleeve and injector hose.
Trim new injector hose to match length of removed hose (I cut off abt 4 inches)
Install injector hose and plastic sleeve. Ensure clocking is correct on hose.
Install gasket on fill hose fitting.
Insert fitting into tub. Rotate 90 deg CW to latch.
Install gear clamps loosely on fill tube.
Attach fill tube to fill fitting and injector sleeve.
Slide clamps onto tube ends ensuring clamp clocking provides access and clears tub top..
Test tub fill to ensure injector works without leaks
Remove front washer panel screws.
Remove bolts holding front of top to side panels
Remove hose clamp from front hose to injector sleeve.
Twist fill hose ccw 90 degrees at tub fitting to remove.
Clean corrosion at tub attachment point wuth wire brush.
Paint bare metal to seal. Allow to thoroughly dry.
Remove injector sleeve and injector hose.
Trim new injector hose to match length of removed hose (I cut off abt 4 inches)
Install injector hose and plastic sleeve. Ensure clocking is correct on hose.
Install gasket on fill hose fitting.
Insert fitting into tub. Rotate 90 deg CW to latch.
Install gear clamps loosely on fill tube.
Attach fill tube to fill fitting and injector sleeve.
Slide clamps onto tube ends ensuring clamp clocking provides access and clears tub top..
Test tub fill to ensure injector works without leaks
Other Parts Used:
-
Padraic from SAINT PAUL, MN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking at top of tub when filling with water
Did repair as instructed by video, I'm 74 years old if I can do it anybody can!
Other Parts Used:
-
Frank from Patterson, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaking when in use ,upper back left side
unplug machine ,shut off water supply,Removed 2 lower front panel screws ,raise panel upward "hinge type motion"and removed , Remove 2 self tapping screws from under front corners, removed liquid bleach tube from upper connector ,raise top toward back of machine , place prop "piece of wood" to hold top up,removed 1 screw attaching injector ,now replaced injector assy and install with new hoses and clamps. then assemble in reverse order
Other Parts Used:
-
Kenneth from Franklin, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom Miliano
December 3, 2018
Water appears to leak out of the injector sleeve. The design of this white part appears to be exposed at the top, so i'm not sure how replacing it solves the problem. Wouldn't water naturally shoot out of the exposed top?
For model number Maytag A8200
Hi Tom,
Thank you for your question. If water is leaking out of the injector sleeve, another part may be causing the issue. I would check the rubber injector valve, the nozzle and the injector tube. The leakage could be caused by deposits of water, debris and soap deposits or the water pressure is too low and will not allow that valve valve to expand against the inside of the sleeve and seal. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
January 28, 2019
I noticed my washing machine was leaking water. After troubleshooting i found the water leaking out of (overflowing) injector sleeve if it was set for anything other than cold. Is this a bad injector sleeve or could it be a bad injector pump putting too much hot water through?
Hello Mike, Thank you for your inquiry. It is possible that you need to replace either the injector valve. In order to suggest the correct part numbers we will need the model number of the washer. You can submit a follow up with the model number if you would like. Have a nice day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738910
Manufacturer Part Number: WP215447
Manufacturer Part Number: WP215447
Brand
Model Number
Description