Part Location Diagram of 134051003 Frigidaire Drive Belt
See part F25 in the diagram
Replacing your Frigidaire Washer Drive Belt
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Drive Belt

★★★★★
★★★★★
2 Reviews
$56.55
  On Order
PartSelect Number PS1990787
Manufacturer Part Number 134051003
Manufactured by Frigidaire
Product Description

Drive Belt Specifications

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Washer Drive Belt

Replacing your Frigidaire Washer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Burning smell | Spins slowly
This part works with the following products:
Washer.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 134051003 replaces these:
AP4321740, 1378564, 134051001, 134051002
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.3 / 5.0, 5 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Door lock switch faulty preventing washer from spinning
Codes did not point directly to the door lock, so that was a 50/50 between door lock and control board. With top of washer removed door lock is just a couple screws and 3 electrical connections.

Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.

Works like new!
Other Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Jeff from Thousand Oaks, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
44 of 55 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer will fill and drain but will not spin or agitate
Went by the percentage of people with same problem- door switch was the highest. Ordered door switch and a new belt (belt was getting worn- 6 yrs. old) Door switch did not fix problem. Saw on website that it could be motor control board. Took motor control board out. Nothing visible wrong with anything. Decided not to spend $$ on new board. Figured new washer would be better. Put motor control board back in and tried it......works like new! Must have been a loose wire on the motor control board. Next time I will check wires first. :) Getting motor control board in and out was time consuming but no too hard.
Other Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Gabriel from MERRILL, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
16 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drum pulley kept getting loose and wobbling. Hub wore out making permanent tightening impossible
Simple. Remove the drive belt from the pulley. Next remove the retaining screw and remove the old pulley. Put the new pulley on the hub, then insert the retaining screw and tighten securely. Last, replace the belt over the motor and hub pulley. This was the most difficult part as the new belt was quite tight. But once I convinced myself it was the right belt a little more effort yielded results and the belt fit fine.
Other Parts Used:
Idler Pulley Screw,10.9 class ,M10 x 25 mm
  • Richard from Long Valley, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt was still on washer, had developed a loose tear
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.
Other Parts Used:
  • jeffrey from mount juliet, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no spin, broken handle, everything else worked
after clearing shelving. It took about 20 minutes to remove the dryer stacked on top, along with the gas line and the vent hose.....
Two screws and gently pry the back up with a screwdriver and the top pops off. open the door and remove the 2 screws while reaching down inside and the switch come right up with its 3 plug harness.
swap the old switch unit for the new one and slip it back down into place and reinstall the screws, and done in about 15 minutes.

my belt is in good shape so I will save the one I bought for later.
the handle is 2 screws and took less than 2 minutes.
It took about 20 minute to put the washer/dryer units back together and against the wall and running
Other Parts Used:
Front Load Washer Door Lock and Switch Assembly Door Handle
  • Paul from Fontana, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Veronica
17 days ago
Is this the only part I need to replace and is it easy?
For model number LTF6700FS0
PartSelect logo
Hi Veronica, Thank you for your question. If all the other parts are fine, then you should only need to replace the belt. We would recommend checking the idler pulley that the belt goes on for signs of wear and damage to see if it needs to be replaced also. We hope this helps!

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1990787
Manufacturer Part Number: 134051003
Brand
Model Number
Description
Kenmore
41744052400
Washer
Kenmore
41744052401
Washer
Kenmore
41744052500
Washer
Kenmore
41744082400
Washer
Kenmore
41744082500
Washer
Kenmore
41744092500
Washer
Kenmore
41744152400
Washer
Kenmore
41744152401
Washer
Kenmore
41744152500
Washer
Kenmore
41744252500
Washer
Kenmore
41744252501
Washer
Kenmore
41748102700
Washer
Kenmore
41748102701
Washer
Kenmore
41748106700
Washer
Kenmore
41748112700
Washer
Kenmore
41748112701
Washer
Kenmore
41748116700
Washer
Frigidaire
970L48022A0
Washer - WASHER
Frigidaire
ATF6000ES0
Washer - Residential
Frigidaire
ATF6000ES1
Washer - Residential
Frigidaire
ATF6000FS0
Washer - Residential
Frigidaire
ATF6000FS1
Washer - Residential
Frigidaire
ATF6000FS2
Washer
Frigidaire
ATF6500FG0
Washer - Residential
Frigidaire
ATF6500GG0
Washer - Residential
Frigidaire
ATF6500GG1
Washer - Residential
Frigidaire
ATF6500GS0
Washer - Residential
Frigidaire
ATF6700FE0
Washer - Residential
Frigidaire
ATF6700FE1
Washer - Residential
Frigidaire
ATF6700FE2
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service