KDTE204DSS0 KitchenAid Dishwasher - Instructions

Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

Per suggestions from other reviews, I looked for You Tube videos for replacing this part. The video I used was completely necessary, but moved way too fast, so required lots of stopping, rewinding and starting again. But I managed to get the old rack adjuster removed and the new one installed without too much trouble.
Then I tried installing it in the pull-out rail. The front connector on the new adjuster would not fit into the appropriate slot. Initially I thought maybe the part was defective, but determined that the dimensions were as accurate as my eye and tape measure could evaluate. Finally, I settled on the expedient of filing away at least 1/16" from one edge of the slot so that the connector would drop into place.
Not sure why this discrepancy existed but the problem appears to be resolved.

The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done

removed and installed cords with screw driver

Take out the upper dishwasher rack. Place the adjuster towards the back of the upper each place attachment clips to secure adjuster and the adjuster clips to the back of the housing. Check to back sure adjuster move up and down and click back into place. Your installation is complete. Good luck!

The old filter simply unscrews and the new one screws in.

Pulled out dishwasher, removed 4 bolts holding the track to the dishwasher, replaced track and installed the 4 bolts. Pushed back the dishwasher and works like new. The new tracks are riveted instead of spot weld and will last longer.

This was so simple! Some plastic tabs snapped off the upper rack adjuster in our dishwasher (which is not even 4 years old, so you can see how crappily made these things are), rendering the entire appliance unusable since the water sprayer thingie attaches to the underside of the upper rack. I was able to easily find replacement rack adjusters on PartSelect and thanks to the repair video, was able to install them in about 20 minutes. Most of that was rewinding the video since I had trouble getting the broken adjusters off! So delighted to have been able to do this myself and avoid paying $$$ for a repairman call out and replacement parts.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

Remove entire top rack and place on a large flat work surface. A small screwdriver is needed to release several plastic clips holding the upper drawer slider brackets and manifold in place. Carefully pry the clips free of their mounting holes and remove the bracket. Take some time to study how things are held together before removing anything since one plastic clip is closely affected by the others. Without pictures, and a video, it's really difficult to put into words. I must stress, do not force anything. When disassembling, use the opposite side to as a visual aid to reassemble.

Purchase 4 roller wheel assemblies and installed them with only a screw driver to open the tangs. quick and easy and rack rolls smoothly inside the dishwasher. Rather expensive $58 per roller assembly and hopefully these last the lifetime of the dishwasher.

I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).

By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.

Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.