Fresh Food Door Gasket

The old gaskets were easy to pull out. At first I thought the bead of the new ones were supposed to slide into place. Then I just loosened the phillips head screws that hold the inner door panel. I loosened them all and pried the inner door out about 4 mm. the the bead of the new gasket slid in with relative ease. Then I tightened the screws back up, I just had to peel back the gasket to get at each one. The gasket holds itself in place with no adhesive.

Door would not stay closed so I decided to replace the gasket... The new gasket install was easy and quick. I removed the liner and took off the old gasket, placed the new gasket on the liner and reinstalled the liner. However that did not fix the original issue of the door not closing. I followed all the instructions listed on the web site but none corrected the problem. The door on this model has no adjustment. So I adjusted the leveling wheels to tilt off center towards the back. That helped but still did not resolve the problem... I then closed the door slowly to see if it was being interfered with, As it turns out it was being hit by the bottom of the inside of the refrigerator. Since I could not adjust the door, I used the front leveling wheels to compensate for the lack of door adjustment. I slowly kept adjusting the w heels to see what effect it had. I finally adjusted them to the point were the door now closes and seals on its own. I’m guessing that over time the liner became malformed and caused the door to hit the inside of the refrigerator. After it started working I checked the level side to side and front to back. Side to side is good and there is a slight tilt to the rear.

My husband and I were online pricing new refrigerators ($1100 and up plus an otherwise okay frig to add to the landfill). I had a moment of clarity and tried a parts search and found this site. I decided we were NOT going to replace it, we would fix it.

I pulled out the entire shelf and unscrewed the rail. I manuevered in the new rail and screwed it down. I returned the shelf and now I no longer have the deli drawer drop out of the tracks.

To replace the gasket, the worse part was having to empty the contents of the door and removed all of the 30+ screws that hold it in place. I positioned the gasket over the edge of the door inset, pressed it back up against the door with the gasket in place, lined up the screw holes and started turning the screwdriver. I screwed in the top 2 corners first so they would hold the door inset in place from that point.

The instructions stated that silicon sealant should be applied between the gasket and the door, particularly at the corners, and I did this, particularly since the corner pulling out was why I was replacing the gasket in the first place.

However after I returned all the screws to the proper place and turn the refrigerator back on, I noticed condensation around the seal. I realized after a few days that I had silicon on the gasket itself and this was causing an imperfect seal. I cleaned all the little wisps of silicon off the gasket and the frig has been fine ever since.

Removed old gasket. tried to mount new gasket with a few screws, but weight of new gasket created a sag, so I removed door and laid on a table. Installed new gasket, as it layed flat and square on the table. Installation became a simple job.

First I let the gasket lay flat on a hard surface in the sun for several hours. Then I removed old gasket and placed new gasket in place and utilized some glue substance to hold it in place.
Easy enough--hope refrigerator will be more energy efficient

Simply removed (many) screws from the door shelving panel. Removed old gasket, installed new one and screwed it back on. A rather simple repair that will allow me continued use of my older fridge.

Removed all the screws. Replaced the gasket put all the screws back. This would work great if the door wasn't out of alignment.

Now I have a new refridgerator coming on Monday.

took off the old one installed the new one

First I removed the old gasket by pulling it off the door. Then I removed the screws from the door. Next I placed the new gasket around the door frame. Finally, I replaced the screws in the door to completely attach the gasket.

door gasket: removed all the screws in the door panel,removed old gasket and fitted the new one and then replaced all the screws while making sure the gasket was in place.
Door shelf brackets: removed old broken ones and snaped the new ones in place.